Hitachi RAS-E08H2A Service Manual page 12

HOW TO SET THE TIMER
Time
TIME
(current time)
After you change the
batteries;
OFF TIMER
ON TIMER
OFF-Timer
RESERVE
Start
CANCEL
You can set the device to turn off at
the present time.
ON-Timer
The device will turn on at the
designated times.
1
ON/OFF-Timer Press the
TIMER) button so that
the (OFF) mark
Start Stop
blinks.
• The device will turn on (off) and
off (on) at the designated times.
PM
• The switching occurs first at the
preset time that comes earlier.
• The arrow mark appearing on the
display indicates the sequence of
switching operations.
How to Cancel Reservation
Point the signal window of the remote controller toward the indoor unit, and press the
button.
The (RESERVED) sign goes out with a beep and the
NOTE
You can set only one of the OFF-timer,
ON-timer and ON/OFF-timer.
1
Set the (TIME) button.
AM
PM
1
Press the (OFF-TIMER)
button. The (OFF) mark blinks
on the display.
Stop
AM
1
Press the (ON-TIMER)
button. The (ON) mark blinks on
Stop
Start
the display.
AM
2 3
(OFF- Set the turn-off time Press the
with the TIMER control TIMER) button so that the
button. (OFF) mark lights and
Press the (RESERVE)
the (ON) mark blinks.
button.
PM
PM
AM
(CANCEL)
(TIMER) lamp turns off on the indoor unit.
– 12 –
2
Set the current time with
the TIMER control button.
PM
Example: The current time is 1:30p.m.
2
Set the turn-off time with
the TIMER control button.
PM
2
Set the turn-on time with
the TIMER control button.
AM
4
Set the turn-on time with
(ON-
the TIMER control button.
PM
AM
• The timer may be used in three ways: off-timer, on-timer and ON/OFF (OFF/ON)-timer. Set the
current time at first because it serves as a reference.
• As the time settings are stored in memory in the remote controller, you only have to press the
(RESERVE) button is order to use the same settings next time.
3
Press the (TIME)
button again. The time
• The time indication will disappear automatically in 10
seconds.
indication star ts lighting
instead of flashing. • To check the current time setting, press the
button twice.
The setting of the current time is now complete.
PM
3
Point the signal window of the remote controller toward the indoor unit,
and press the (RESERVE) button.
The (OFF) mark starts lighting instead of flashing and the
sign lights. A beep occurs and the (TIMER) lamp lights on the indoor unit.
Example: The device will turn off at 11:00p.m.
PM
The setting of turn-off time is now complete.
3
Point the signal window of the remote controller toward the indoor unit,
and press the (RESERVE) button.
The (ON) mark starts lighting instead of flashing and the
sign lights. A beep occurs and the (TIMER) lamp lights on the indoor unit.
Example:
The device will turn on early so that the preset
temperature be almost reached at 7:00 a.m.
AM
The setting of the turn-on time is now complete.
5
Point the signal window of the remote controller toward the indoor unit,
and press the (RESERVE) button.
The (ON) mark starts lighting instead of flashing and the
sign lights. A beep occurs and the (TIMER) lamp lights on the indoor unit.
PM
Example:
For heating, the device will turn off at 10:30 p.m.,
and then turn on early so that the preset
temperature be almost reached at 7:00 a.m.;
for cooling and dehumidifying, it will simply
AM
turned on at 7:00 a.m. The settings of the turn
on/off times are now complete.
– 13 –
(TIME)
(RESERVED)
(RESERVED)
(RESERVED)