Page 2
PLEASE CHECK FOR CHANGE INFORMATION AT THE REAR OF THIS MANUAL. OSCILLOSCOPE INSTRUCTION MANUAL Tektronix, Inc. P.O. Box 500 a..verton, Oregon 97077 Serial Number Printing FIrSt APR 1975 070-1878-01 Reviled APR 1986 Product Group 75...
se 502 SERVICE SAFETY SUMMARY FOR QUALIFIED SERVICE PERSONNEL ONL Refer also to the preceding Operators Safety Summary. 00 Not ServIce Alone Disconnect power before removing protective panels, soldering, or replacing components. Do not perform Internal service or adjustment of this product unless another person capable of rendering first aid and resuscitation is present.
1-IC 502 Sedton SPECIFICATION Pert�nc. Condition. Any conditions that are uniQue to a particular ctlaracter· Istic expressly stated as part of that characteristic. characteristics in this specifica tion valid eIectricaJ the following condition s : wTth The Instrument must have adjusted at been ambient temperature...
Page 10
Ipec:tflcatlon-SC S02 Cta.Jactwlttt ca Performance R�ulr Suppl .. Information ..ent. . nt ..10Hz with ooup/ing 1 Hz less X10 probe. Response or less with Common Mode ReieC1iOn Ratio At least 30 to 1 at 1 MHz less with same Common...
SpKlflcallon-$C 502 Table 1·3 TRIGGERING SYSTEM Supplemental Information Performance Requirement. Characterisllcs Trigger Sensitivity (Minimum peak.to-.peak signal Extemal quired) CH1 or CH2 60mV O.4div 5 MHz or less 150 mV 5 MHz 1.0 div 15 MHz Coupling Minimum signal requirements extend to Minimum signal requirements wease be·...
Spedflcatlon-SC TatMe CATHODE RAY TUBE Characteristics Performanca Requirements Supplemental Information CAT Type T3350 . Graticule 8 X 10 divisions with 0.25 inch/division (0.64 an/division). Phosphor P31. Acceleration Potenlial 12 kV (-1.9 kV cathode). Geometry and Orthogonality Bowing or tilt is 0.1 division or Jess with respect to graticule lines.
Speclflcatlon-se CNr'actertltlcs p.,formanc. Requlrementl Supplemental Inform.tlon TypieaUy watts less operating, less Mainframe Power Una Draw than 1 watt with mode switCh set to POWER OFF, hOurs 1000 Recommended Adjustment 6 months, Interval Warmup Time 20 minutes, 60 minutes after exposure to storage in high humidity (condensing) environment.
Page 15
Spedtlcatlon-SC 1·8 Ta"'e ENVIRONMENTAL- Chliracteriatica Description Temperature Meets MIL-T-28800B, Class 5. Operating O·C to +SO·C. -55 ·C to + 75-C. on-oper Humidity O·C to +30·C. Exceed s MIL·T·28800B, class 5. o +40·C. o +5D·C. RH, t Altitude Exceed s MIL-T-28800B, class 5. ttl.
Power Module. in; otherwise, damage may occur to the plug-in Recommended probes for use with the SC 502 are the circuitry. P61OS, PS062B, and P6060. The P60628 probe has a selectable 1X or lOX attenuation while the attenuation o f P610S is lOX.
OpMatlng Inltructlonl-Se NOTE Adjust the channel and horizontal POSITION con trols so that the display is centered vertically and starts at The vertical ligfltfy shaded araas on the front panel the left edge of the graticule. behind the VOL TS/DIV and SECONDS/DIV knob skirts highlight the basic sensitivi t y and sweep rate selected.
Page 19
® POWER Indicator. The light indicates that t�e CAL Variable Control. Provides variable un is turned on. SC 502 power calibrated deflection factors between calibrated seuings of the VOL Ts/DIV switch. ® RESET Pushbutton. Push to arm the sweep in single sweep operation.
Page 30
WARNING SERVICING FOLLOWING INSTRUCTIONS QUALIFIED PERSONNEL ONLY. TO AVOID PERSONAL INJURY, DO NOT PERFORM ANY SERVICING OTHER THAN THAT CONTAINED OPERATING INSTRUCTIONS QUALIFIED UNLESS REFER OPERATORS SAFETY SUMMARY AND SERVICE SAFETY SUMMARY PRIOR TO PERFORMING ANY SERVICE.