Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for VARILITE ICON BACK SYSTEMS
Summary of Contents for VARILITE ICON BACK SYSTEMS
- Page 1 WITH VARILOCK™ HARDWARE Installation Instructions This manual explains how to install, operate and maintain the Icon Back System. If you do not understand this instruction manual or if you have any questions, please contact VARILITE Customer Service at (800) 827-4548...
-
Page 3: Table Of Contents
Installation Instructions Table of Contents Icon Back System Styles Page 4 WARNINGS Pages 5-9 Icon Back System Components Page 10-11 Assembly and Mounting Steps Page 12 Adjustment Steps Page 13-14 Operating Instructions Page 15 Back Cushion Instructions Page 16 Thoracic Support Page 16 Troubleshooting Page 17... -
Page 4: Icon Back System Styles
Installation Instructions ICON Back System Styles These instructions are applicable to the following Icon Back System Styles M i d L o w T a l l D e e p Page 4 © 2013 Cascade Designs, Inc. -
Page 5: Warnings
• Never use the back support without its cover. The cover is made with flame retardant materials. Using the back support without its cover increases the risk of flammability. • Never modify your VARILITE back support or use it in a way not described by these instructions. Page 5... - Page 6 Failure to use the appropriate equipment for restraint in a vehicle can result in serious injury or death. For additional information regarding the use of seating systems in motor vehicles, refer to Safe Use in a Motor Vehicle provided with this system and at www.varilite.com Page 6 © 2013 Cascade Designs, Inc.
- Page 7 Installation Instructions Wheelchair Compatibility WARNING VARILITE back systems are designed to be compatible with most wheelchairs, noting the following exceptions: The system can be used only with wheelchairs with cane diameters equal to 1 in. (25 mm) or less. The system can be used only with wheelchairs with round canes.
- Page 8 Installation Instructions Wheelchair Compatibility INCORRECT Fig. 1 CORRECT Fig. 2 Page 8 © 2013 Cascade Designs, Inc.
- Page 9 Installation Instructions Wheelchair Compatibility WARNING Failure to install and use Cane Bracket Shims as instructed can result in equipment breakage and serious injury. Cane Brackets are sized for 1 in. (25 mm) diameter wheelchair canes. Shims are provided for wheelchair canes that are less than 1 in. (25 mm) in diameter.
-
Page 10: Icon Back System Components
Installation Instructions ICON Back System Components Please familiarize yourself with the parts of the back system before installation, adjustment or use. Cane Hardware CANE BRACKET Components ADJUSTER PLATE 1. Cane Bracket 2. Holster 3. Adjuster Plate SLIDE 4. Slide Cap 5. - Page 11 Installation Instructions ICON Back System Components Self-Inflating Cushion and Valve Shell Interior Handle Flap and Handle Patch Page 11 © 2013 Cascade Designs, Inc.
-
Page 12: Assembly And Mounting Steps
Installation Instructions Assembly and Mounting Steps Adjustment may be necessary to complete the installation and accommodate the width of the wheelchair, or for desired seat depth, angle and height. The following steps must be done before the client is in the wheelchair: 1. -
Page 13: Adjustment Steps
Installation Instructions Adjustment Steps The following steps can be done with or without someone in the wheelchair: Depth and Angle Adjustments 1. Loosen the two Cane Bracket Adjustment Screws and adjust for desired level of depth and angle. Only loosen adjustment screws 3/4 of a turn to slide. - Page 14 Installation Instructions Seat Depth Adjustment Seat depth adjustment varies according to the clinical application and the recline angle of the back. In most cases, Icon Back System hardware allows seat depth to be adjusted so that the back does not take up seat depth in front of the canes. Icon Back System hardware also may be installed anterior of the canes in situations where seat depth is desired for growth.
-
Page 15: Operating Instructions
Installation Instructions Operating Instructions Removing the Icon Back System 1. Depress buttons and slide the left and right Slide Caps open. 2. Grab the top of the shell and lift up until the Slide Bars clear the Holster. 3. Slide the left and right Slide Caps closed, towards the Shell. Inserting the Icon Back System 1. -
Page 16: Back Cushion Instructions
3. When cushion is fully inflated, close air valve by turning valve clockwise. Adjusting Cushion 1. To adjust the air level of the VARILITE back support, begin with the cushion fully inflated and the valve closed. 2. Position wheelchair user securely in wheelchair. -
Page 17: Troubleshooting
Installation Instructions Troubleshooting The Icon Back System should operate smoothly. The back support should remove and insert without binding. If the back support binds or seems “sticky” during removal and insertion, quick and easy adjustments will correct the situation. 1. Check the back height. Ensure that the Cane Brackets are installed at the same height and are parallel. -
Page 18: Warranty
A returned product deemed irreparable becomes the property of VARILITE, and will not be returned. EXCLUDING THE LIMITED WARRANTY PROVIDED ABOVE, VARILITE, ITS AFFILIATES AND THEIR... -
Page 19: Care And Maintenance
• T he self-inflating cushion can be wiped with a damp cloth. • T he cushion cover can be removed and washed. Machine wash at 140° F (60° C). Air dry. • Never store your back support in conditions of extreme heat or exposure to direct sunlight for long periods of time. • Never store sharp or heavy objects on top of your back cushion. • Once a week, leave valve open overnight, allowing cushion to fully inflate in an unloaded state. Contact Information VARILITE 4000 1st Ave. S Seattle, WA 98134 Phone: (206) 505-9500 Toll Free: (800) 827-4548 Fax: (206) 343-5795...
Need help?
Do you have a question about the ICON BACK SYSTEMS and is the answer not in the manual?
Questions and answers