Related Manuals for Panasonic ES7036-E8
Summary of Contents for Panasonic ES7036-E8
- Page 1 ORDER NO. SD0509E44C8 Wet/Dry Rechargeable Shaver ES7036-E8 / ES7038-E8 SPECIFICATIONS SPECIFICATIONS 2005 Matsushita Electric Works, Ltd. All rights reserved. Unauthorized copying and distribution is a violation of law.
-
Page 2: Schematic Diagram
1. SCHEMATIC DIAGRAM 1.1. ES7036 1.2. ES7038 2. WIRING CONNECTION DIAGRAM 3. DISASSEMBLY INSTRUCTION Follow the procedure below to disassemble the main unit. 1. Remove the cap, the outer foil with foil frame and the inner blade. - Page 3 2. Slide the trimmer handle up to open the trimmer and unhook the trimmer handle by inserting something like a sloted screwdriver or plastic spatula into a slit. NOTE: Make sure not to scratch or damage on the housing. 3. Remove trimmer and trimmer handle.
- Page 4 4. To remove the trimmer driving bar or the slit blade driving bar, press bars outward. 5. Loosen a screw and remove the bottom cover. 6. Slide down the side panels for both sides.
- Page 5 7. Loosen two screws on front and four screws on the back side, and remove two housing clips. 8. Take out the housing B.
-
Page 6: Caution In Assembly
9. Remove the motor assembly and tube holder. 10. And take out the battery assembly from housing A. 11. Remove the battery o-ring and washer in each battery. Take out the rechargeable batteries from the chassis. 4. CAUTION IN ASSEMBLY... -
Page 7: Rechargeable Batteries
NOTE: When reassembling, replace the new waterproof rubber. Make sure whether there is NO foreign substance sticking around a part covered with water seal. 4.1. Motor Insert the motor and press fit the waterproof tube neatly under the tube holder. And put the float spring propery. - Page 8 4.3. Module Align the projection of switch select button on housing A with the groove of switch plate on module. 4.4. Driving bars Set the trimmer driving bar and the slit blade driving bar.
-
Page 9: Side Panel
4.5. Side panel Set the side panel on the body and slide it up until clicking the hook of panel at three locations. NOTE: Make sure that the left and right side panels are firmly fitted on both rear and front side. Fit the front side of hook first, then on top and rear side. -
Page 10: Troubleshooting Guide
5. TROUBLESHOOTING GUIDE (Refer to WIRING CONNECTION DIAGRAM) <TROUBLE> <CHECK.> <REMEDY> Motor does not <CHECK CHARGING ADAPTOR.> NO Replace charging rotate. Does not Connect the rated voltage to the normal main unit by the adaptor. charge. charging adaptor. Functions for a Check if the charge status lamp of main unit is lit. - Page 11 (Replace two rechargeable batteries at the same time even though one battery is defective due to series connection.) <CHECK SWITCH CONTACT.> NO Repair contact replace Okay if there is a continuity and no deformation of switch housing A. terminals. <CHECK MOTOR.> NO Replace motor.
-
Page 12: Exploded View And Replacement Parts List
6. EXPLODED VIEW & REPLACEMENT PARTS LIST 6.1. ES7036 NOTE: *A=available as an optional accessory *B=only available as set *C=available individually... - Page 13 Ref. No. Part No. Part Name & Description Remarks Per Unit WES7043X7158 PROTECTIVE CAP (BG) WES9085Y OUTER FOIL WES7046S0047 OUTER FOIL FRAME ES7036S (BG) WES7043H0047 OUTER FOIL FRAME ES7036K (BG) WES9064Y INNER BLADE WES7046L1009 LINEAR MOTOR ASSEMBLY ES7036S (BG) WES7043L1008 LINEAR MOTOR ASSEMBLY ES7036K (BG)
- Page 14 NOTE: *A=available as an optional accessory *B=only available as set *C=available individually Ref. No. Part No. Part Name & Description Remarks Per Unit WES7043X7158 PROTECTIVE CAP (BG) WES9085Y OUTER FOIL WES7046S0047 OUTER FOIL FRAME (BG) WES9064Y INNER BLADE WES7046L1009 LINEAR MOTOR ASSEMBLY (BG) WES7046L1087 TRIMMER DRIVING BAR (BG)
- Page 15 Ref. No. Part No. Part Name & Description Remarks Per Unit WES4025K7007 SOFT CASE (BG) WES8093H7057 CLEANING BRUSH WES7038S8008 INDIVIDUAL BOX (BG) WES7036S8108 OPERATING INSTRUCTIONS (BG)