YZ-X2 Content Chapter 1 Description 1.1 Content and Purpose................4 1.2 General Instructions.................4 1.3 Safety requirements for batteries.............5 1.4 General safety regulations............... 6 Chapter 2 Use of the Machine..............6 2.1 Buttons/Panels of the Machine............6 2.2 The operation process of the machine..........8 2.3 Precautions for machine operation..........10...
YZ-X2 Chapter 1 Description 1.1 Content and Purpose The following content points out potentially dangerous situations, please read these instructions carefully and take necessary precautions. The essence of this machine operator's manual is to prevent injuries, and most accidents are caused at work by not heeding basic safety rules.
YZ-X2 ●Do not use the machine where the inclination exceeds the rated value of the machine. ●Please do not smoke while charging the battery. ●Do not use the machine in a very dirty area. If the road garbage is thick, please repeat the sweeping work twice or more.
YZ-X2 battery wire. When rewiring, be sure to pay attention to the polarity of the battery, as wrong connection will damage electrical components. ●Avoid direct contact between the positive electrode and the negative electrode, because it will cause a large current short circuit, generate high heat and even cause a fire.
Page 9
YZ-X2 2.1.2 Charging the battery ●The charging socket cable requires at least a power cable with a diameter of 4mm. ●Note: The charger is placed on a stable platform, pay attention to moisture-proof, anti-moisture Water and drop resistant. ●The charging time must be guaranteed for 6-10 hours per charge.
YZ-X2 from wear and tear. For installation, refer to "3.2 Brush plate replacement and installation" for operation. 2.2 The operation process of the machine Before start ●Before the normal operation of the machine, make sure that the squeegee is installed correctly, and the sewage suction pipe is inserted into the suction port.
Page 11
YZ-X2 Start the machine Step 1: Lightly step on the foot lever Step 2: Open the water valve; and put down the scrubber; Step 3: Turn on the main power switch, Step 4: Tighten the handlebars and keep driving at a constant speed.
YZ-X2 2.3 Precautions for machine operation Machine Operation Precautions ●Avoid stopping the machine for a long time in the same place and let the brush clean; this will leave unnecessary marks on the ground. ●When cleaning the floor is epoxy floor, it is necessary to add a cleaning pad to avoid the abrasion of the epoxy floor by the brush.
YZ-X2 Machine storage and maintenance If the machine will not be used within 30 days, please fully charge the battery, disconnect the positive and negative output wires of the battery, and place the machine in a dry and clean place.
YZ-X2 Whether the main brush is wired, the silk is entangled Check for debris in the tank Check the buttons and electronics on the control panel Check the brush for wear Check the filter for impurities Check the sprinkler joint for leaks 3.2 Brush disk replacement, installation and...
YZ-X2 to the previous article for the installation of the dial on the machine; ●Brush plate adjustment: When the machine is in the process of cleaning and driving, when the left deviation occurs, it needs to be loosen the direction screw; on the contrary,...
YZ-X2 Step 3: Align the Step 1: Align the Step 2: Fix the plastic holes of the rear holes of the front components on the rubber strip with the rubber strip with the cast aluminum base plastic components of protrusions of the...
YZ-X2 ! ! Warn During the use of the battery, the battery is deeply discharged, the battery capacity will be reduced, and the lifespan will be shortened. 3.5 Maintenance and disassembly of suction motor ●After the daily use of the machine, please discharge the sewage...
YZ-X2 3.6 Fuse removal In the daily use of the machine, if the fuse is burned out, or the fuse needs to be checked due to machine failure, refer to the following steps to operate: The first step is to open the water tank, drain the sewage and clean water, and open the outer cover of the electrical box.
Page 19
YZ-X2 Chapter 4 Analysis Table of Common Problems of Floor Scrubber Problem Cause Solution Battery charging Battery dead Replace the battery Battery failure Machine is inoperable Tighten the battery wiring Battery wiring loose Main fuse blown Replace the fuse The brush head is lifted off the...
YZ-X2 Chapter 5 Maintenance Machine life and operational safety must be ensured by proper and routine maintenance of the machine. The routine maintenance requirements are tabulated below. Under suitable working conditions, the maintenance interval can be changed, which must be determined by the professional responsible for the maintenance.
Page 21
YZ-X2 Warranty Warranty is not covered under the following conditions of use: ● Failure to perform maintenance in accordance with the maintenance manual may result in mechanical damage or failure. ●The mechanical appearance or structure is obviously damaged due to improper operation.
Page 22
YZ-X2 4. During the warranty period, users who do not follow the operating instructions or those who dismantle and repair by themselves will not be covered by the warranty (if repair is required, a cost will be charged); 5. The buyer can go to the designated point of the seller for maintenance with the invoice, or send the machine back to our company for repair (return freight and insurance premiums are paid by themselves).
Need help?
Do you have a question about the YZ-X2 and is the answer not in the manual?
Questions and answers