Subscribe to Our Youtube Channel
Related Manuals for GCAN GC-2008
Summary of Contents for GCAN GC-2008
- Page 1 GC-2008 8-channel digital output module (PNP) User manual Document version 3.02（2020/10/27）...
- Page 2 Vhandy technology GCAN-2008 user manual Revision History Version Date Reason V1.00 2015/09/16 Create V2.01 2015/12/20 Modify device parameters V3.01 2017/10/22 Add parameters V3.02 2020/10/27 Modify device appearance picture...
-
Page 3: Table Of Contents
2. Installation ....................... 5 2.1 Module fixing ....................5 2.2 Wiring method ....................5 2.3 System statusindicator ................... 7 2.4 Combined with GCAN-PLC-400/510series ..........7 2.5 Combined with GCAN- 8000series ...............8 3. Technical Specifications ..................9 4. Disclaimer ......................10 5. Module selection table ................... 11... -
Page 4: Introduction
1. Introduction 1.1 Overview The GC-2008 module has integrated 8 digital output channels, which acquires digital signals in real-time and transmits them to the GCAN-PLC coupler. This module can be used with any other GC Series IO module to capture and process digital data in industrial automation or distributed control systems. -
Page 5: Installation
Installation of GC-2008 module First install the GCAN-PLC on the guide rail and plug the GC-2008 along GCAN-PLC's right side until the lock is stuck. When remove the GC-2008, the user need to release the self-locking mechanism by pulling out the orange label. - Page 6 Vhandy technology GCAN-2008 user manual Figure 2.2 Wiring method of GC-2008 module Figure 2.3 GC-2008 module terminal definition...
-
Page 7: System Statusindicator
The GC-2008 module has no error indicator. The user can determine the status through the "IO RUN" and "IO ERR" indicators of the GCAN-PLC. If the "IO ERR" indicator of the GCAN-PLC lights up, it indicates that the IO module is not working properly. -
Page 8: Combined With Gcan- 8000Series
For example, when GCAN-8000 module node number is 1, the output state of channel 8 and channel 4 of the first GC-2008 module is logic "1", and the output state of other channels is logic "0", the CAN data frame ID sent by the GCAN-IO-8000 module is 0x181,the data length(DLC) is 8, and the frame data is 0x88, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00.Please note that when only one GCAN-2008 module is... -
Page 9: Technical Specifications
500 V（GC-bus/ Signal voltage） 120mA Current consumption Bit width output 1 byte in the process image Installation position In sequential order Power supply Powered by GCAN-PLC, current consumption 100mA Environmental testing -40℃~+85℃ Operating temperature Permissible relative 95%RH，no condensation humidity EN 55024:2011-09... -
Page 10: Disclaimer
4. Disclaimer Thank you for purchasing GCAN's GCAN series of hardware and software products. GCAN is a registered trademark of Shenyang Vhandy Technology Co., Ltd. This product and manual are copyrighted by Vhandy Technology. Without permission, it is not allowed to reproduce in any form. Before using, please read this statement carefully. -
Page 11: Module Selection Table
Vhandy technology GCAN-2008 user manual 5. Module selection table GCAN-PLC-400 series products consist of a programmable main control module, several GC series IO modules and a terminal resistance module. GC series IO modules currently include five categories: digital input, digital output, analog input, analog output, and communication extension. - Page 12 Vhandy technology GCAN-2008 user manual GC-3844/3854/3 K type / S type / T type Thermocouple 4-channel thermocouple GC-4602 Voltage output, 16 bits -5V~+5V 2-channel GC-4622 Voltage output, 16 bits -10V~+10V 2-channel GC-4642 Current output, 16 bits 0-20mA 2-channel Analog GC-4652...
-
Page 13: Sales And Service
Vhandy technology GCAN-2008 user manual Sales and service Shenyang Vhandy Technology Co., Ltd. Address: Room 401, D11 Block, SISP., Hunnan District, Shenyang, Liaoning, China E-mail: sygckj@gmail.com Tel/ Whatsapp: +86 13644001762 Skype：live:sygckj WeChat: gckj777 Website: gcanbus.com...
Need help?
Do you have a question about the GC-2008 and is the answer not in the manual?
Questions and answers