Page 1
BULL OUTDOOR PRODUCTS BRAHMA 38 INCH GRILL HEAD OWNERS MANUAL FOR MODELS #57568 (L.P.) & #57569 (N.G.) WARNING DANGER Do not store or use gasoline •...
We care about your safety, so please …. READ THIS ENTIRE MANUAL CAREFULLY AND RETAIN FOR FUTURE REFERENCE. • BE SURE YOUR GRILL IS PROPERLY INSTALLED, ASSEMBLED AND CARED FOR. FAILURE TO FOLLOW THESE INSTRUCTIONS MAY RESULT IN SERIOUS BODILY INJURY AND/OR PROPERTY DAMAGE. IF YOU HAVE QUESTIONS CONCERNING ASSEMBLY OR OPERATION, CONSULT YOUR DEALER, GAS APPLIANCE SERVICE REPRESENTATIVE OR YOUR GAS COMPANY. • NOTE TO INSTALLER: LEAVE THESE INSTRUCTIONS WITH THE CONSUMER AFTER INSTALLATION. • THIS OUTDOOR COOKING GAS APPLIANCE IS NOT INTENDED TO BE INSTALLED IN OR ON RECREATIONAL VEHICLES AND/OR BOATS. TABLE OF CONTENTS PAGE # REGISTERING YOUR GRILL & SERIAL NUMBER LOCATIONS REPLACEMENT PART ORDERING REPLACEMENT PART LIST REPLACEMENT PART LIST ILLUSTRATIONS ROTISSERIE SYSTEM PARTS LIST WITH ILLUSTRATION& INSTALL INSTRUCTIONS GRILL OPERATIONAL SAFETY GENERAL SAFETY GUIDELINES 'WHAT TO DO' IF YOU SMELL GAS, GRILL LEAK CHECK INSTRUCTIONS...
REGISTERING YOUR GRILL For Warranty Claims or Replacement Parts ordering, please Thank you for purchasing your Bull fill out the area provided below: Outdoor Products Grill. To validate your PRODUCT INFORMATION REFERENCE CARD Limited Warranty, you must submit the completed the Warranty Registration 1) Model #______________________________ Form within 90 days from the date of 2) Serial #_______________________________ purchase. Registration can be completed (The Serial Number is encoded with essential information on‐line at ...
BRAHMA GRILL REPLACEMENT PARTS LIST MODEL #57568 LP & #57569 NG (Any item with an * next to it requires a serial number ITEM # NO. USED IN DESCRIPTION BULL PART NO. WARRANTY PERIOD (YEARS) MANUAL PARTS LIST SERIAL NUMBER REQUIRED REF DRAWING 57003 INSERT ASSEMBLY (2016 &...
ROTISSERIE SYSTEM PARTS LIST WITH EXPLODED ILLUSTRATION AND INSTALL INSTRUCTIONS PARTS DESCRIPTION 16552 110 VAC MOTOR W/SWITCH 16554 MOTOR MOUNT BRACKET 16618 38" GRILL SPIT ROD 16553 LARGE 4-PRONG SPIT FORK 16591 SHAFT COLLAR 16587 1/4-20 X 1/2 THUMBSCREW 16675 KEY WASHER 16586...
GRILL OPERATIONAL SAFETY (CONTINUED) WARNING! FOR YOUR SAFETY... DO NOT store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. DO NOT store empty or full spare gas cylinders and/or chemicals under or near this or any other appliance. Keep the fuel hose away from hot surfaces.
LIQUID PROPANE (LP) SAFETY GUIDELINES Your Propane gas grill is designed to operate on propane gas ONLY, at a pressure regulated at 11” water column (W.C.) when equipped with the correct propane orifices on the valves and a propane regulator on the supply line regulated at the residential meter.
NATURAL GAS CONNECTION TO GRILL Bull Outdoor Products does not recommend the use of any quick IMPORTANT: connect fittings or lines to the unit. Use of these types of fittings or lines could cause low gas flow and greatly reduce the performance of the unit . ...
Page 11
THE LOCATION AND INSTALLATION OF YOUR GRILL PLEASE READ THESE INSTRUCTIONS BEFORE INSTALLING YOUR GAS GRILL Your Built-in Gas Grill comes to you fully assembled. We strongly recommend professional installation and hook up of the Gas BBQ grill. These instructions will provide you with the measurements necessary for you or your builder to construct a masonry structure for your outdoor gas grill.
Page 12
GRILL VENTILATION INSTRUCTIONS WHEN USING BUILT-IN CABINETS 1) Upper and lower level vents must be provided for combustion air on both sides of built-in cabinet. 2) Vents on BBQ insert must remain unobstructed to allow for combustion air and ventilation. 3) Upper vents must be located within 5 inches/12.7 cm/127 mm from the top of the island enclosure to the bottom of the vent.
LIQUID PROPANE GRILL INSTALLATION SPECIFICATIONS Vents must be provided for combustion air and ventilation on both sides of built-in cabinet. When choosing a location for your gas grill keep in mind that it should never be located under any overhead combustible construction.
LP GAS TANK RETENTION GUIDELINES: NOTE: AN LP TANK (CYLINDER) WITHIN AN ENCLOSURE MUST USE A TANK RETENTION SYSTEM TO PREVENT BEING KNOCKED OVER. Below are guidelines and illustrations for an LP Tank enclosure and how to install a Tank Retention System which can be obtained through your Bull Dealer: Any Tank Retention system must be secured to the floor using bolts and nuts or lock washers. Once secured, place the LP tank in the tank retention system and tighten the tank retention bolt clockwise until the tank is held snug and cannot move.
A suitable coating of corrosion protection will retard the effects of corrosion and help your Bull purchase last longer. IMPORTANT: Bull Outdoor Products does not recommend the use of any quick connect fittings or lines to the unit. Use of these types of fittings or lines could cause low gas flow and greatly reduce the performance of the unit.
GRILL LIGHT SYSTEM TRANSFORMER INSTALLATION NOTE: Per illustration below, the transformer must be installed at least 6” above the ground to ensure transformer and interior light system longevity. The transformer has mounting holes so you can fasten to the frame inside your island or grill enclosure. Since we don’t know what material, you’ll be mounting to you’ll need to provide your own fasteners to complete.
GRILL ‘FIRST USE’ LIGHTING PROCEDURE • DO NOT SMOKE WHILE LIGHTING GRILL OR CHECKING GAS SUPPLY • CONNECTIONS BECOME FAMILIAR WITH THE SAFETY GUIDELINES AT THE FRONT OF THE MANUAL • DO NOT LEAVE GRILL UNATTENDED DURING USE • DO NOT MOVE GRILL DURING USE •...
GRILL STANDARD LIGHTING PROCEDURE DO NOT SMOKE WHILE LIGHTING GRILL OR CHECKING GAS SUPPLY CONNECTIONS! Set ALL BBQ Grill control knobs to “OFF” and open gas supply, LP cylinder or Control Knob Control Knob LIGHTING MAIN BURNER(S): Natural Gas Valve. ‘OFF’...
Page 19
MANUALLY LIGHT GRILL WITH A FIREPLACE-TYPE MATCH To light gas grill with a fireplace-type match, NOTE: follow steps 1 through 6 on page 16. Remove cooking grid and flame tamer from burner you wish to light. Using provided Lighting Rod to hold a lighted fireplace type match or long-necked butane lighter placing flame near to burner ports.
COOKING COMPONENT INSTALLATION CAUTION, BEFORE YOU START: 1) Turn off the gas supply at the gas supply source first 2) It is recommended you protective gloves to operate the grill when handling any components with transferred heat temperature. 3) Do not move the grill during use.
ROTISSERIE SYSTEM INSTALLATION The trolley thumb screw should be located on the inside of the grill, screw the knurled nut on next, the counterweight is then added and then screw on the black handle. 1) To adjust the counterweight, loosen the black handle and slide the counterweight up or down to properly position the weight of the food being cooked.
BURNER REMOVAL INSTRUCTIONS Your grill has 5 cast stainless steel burners that have cotter pins to keep the burners in place during shipping. You’ll need to remove the cotter pins to allow burner removal for inspection and or cleaning. The cotter pins can be discarded or retained in case the grill is relocated.
REMOVING CAST SST BURNERS FROM YOUR GRILL (CONTINUED) To remove burners, remove cotter pin and lift the burner out of the retaining hole enough to clear so you slide the burner free from the gas valve tip as shown. To re-install burners, install burner back on gas valve tip far enough to allow the burner retainer post to go back into retaining hole on grill.
INSTALLING BURNERS BACK IN GRILL Note, there’s no need to use the cotter pin while installing the back into position. If is for shipping purposes only. IMPORTANT NOTE Check the burner to make sure it is proper located after replacing. Make sure the valve orifices are inside the burner tubes (see illustration below).
GRILL LIGHTING SYSTEM LIGHT BULB REPLACEMENT INSTRUCTIONS Remove screw with a small Phillips screwdriver. Caution: Glass cover may be loose, ensure the cover is properly supported before completely removing the screw. GLASS COVER There is a metal clip that clamps onto the glass cover and snaps into the light housing on the screw end.
ANNUAL CLEANING & MAINTENANCE (1) Keeping outdoor cooking gas appliance area clear and free from combustible materials, gasoline and other flammable vapors and liquids. (2) Not obstructing the flow of combustion and ventilation air. (3) Keeping the ventilation opening(s) of the cylinder enclosure free and clear from debris. Visually checking burner flames including pilot burner flame if provided, with pictorial representations.
Page 27
CLEANING (CONTINUED) OPERATION INDEX REQUIRED INSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS THAT MUST BE FOLLOWED PER ANSI Z210.58-CSA 1.6-2019 SECTION 4.24.2a FOR ALL OUTDOOR COOKING GAS APPLIANCES. I. Installation must conform with local codes or, in the absence of local codes, with either of the following as applicable: a.
TROUBLESHOOTING NEVER SMOKE DURING TROUBLESHOOTING IF GRILL FAILS TO OPERATE PROPERLY 1) Turn off gas at source, turn control knobs to “OFF”, and wait five minutes before trying again. 2) Check gas supply/connections. Repeat lighting procedure. If Grill still fails to operate properly, TURN “OFF” GAS AT SOURCE, TURN CONTROL KNOBS TO “OFF”, wait for grill to cool, and check for the following potential causes below and how to address: MISALIGNMENT OF BURNER TUBE(S) OVER ORIFICE(S) / CORRECTION: Reposition burner tube to properly seat over orifice.
ABOVE LIMITATION MAY NOT APPLY TO YOU. WHO MAY USE THIS WARRANTY? BULL OUTDOOR PRODUCTS, INC. located at address 1011 East Pine St. Lodi, CA. 95240 ("we") extend this limited warranty only to the consumer who originally purchased the product ("you") at the original site of delivery or installation. It does not extend to any subsequent owner or other transferee of the product.
Page 30
Warranty Policy (Continued) Grill Warranty Periods The following parts are covered for one year on all our current gas grill models: he lid, control panel, grease tray, bezels, knobs, temperature gauge, valves, regulator, flex tubes, rotisserie burner, transformer, and all components of the lighting system. The following parts are covered for three years on all our current gas grill models: The manifold, handle end caps, flame tamers, heat shields, and warming rack.
Page 31
Warranty Policy (Continued) WHAT DOES THIS WARRANTY NOT COVER? This limited warranty does not cover any damage due to: (a) transportation; (b) storage; (c) improper installation or use; (d) use on improper fuel/gas supply; (e) failure to follow the product instructions or to perform any preventive maintenance; (f) modifications; (g) unauthorized repair; (h) normal wear and tear;...