Operation; Storage And Transportation - P.I.T. PHE20H-450A Operation Manual

5 Blade
6 Protection sleeve
Technical Data
Model
R e c i p r o c a t i n g f r e -
quency
Weight
Contents of delivery
Hedge trimmer
Blade guard
Instruction manual
Note
In text and numbers, may technical errors and
mistakes be made chat rooms. As the product
is constantly being improved, P.I.T. reserves
the right to make changes to the specifica-
tions and equipment of the product specifi ed
here without prior notice.

Operation

► Pay attention to the mains voltage. The
voltage of the power source must match
the voltage specifi ed on the rating plate of
the machine.
Switching ON/OFF (see fi gures B and C)
For your safety, this tool is equipped with a
dual switching system. To turn on the tool,
press the triggers (2) and (3). Release either
one of the two pressed triggers to turn off.
The sequence of switching is unimportant as
the tool only starts when both switches are
activated.
Working with the Hedgecutter (see
fi gure D)
When cutting new vegetation, use a large
range of motion with the tool so that the stems
fall directly onto the blade.
Wait until the cutting blades reach their max-
imum speed before cutting material. When
working, always keep the blades away from
people and hard objects such as walls, large
stones, trees, cars, etc.
Stop the brushcutter immediately if the blade
becomes stuck. Unplug the hedge trimmer
and remove any jammed debris from the cut-
ting blades.
Wear gloves when cutting prickly or thorny
vegetation.
Move the hedge trimmer so that the branches
fall directly on the cutting edges of the blade.
Do not attempt to cut stems that are thicker
than the blade gap.
Move the hedgecutter evenly forward along
the cutting line.
The double edge cutting blade enables cut-
ting in either direction, or with a side to side
PHE20H-450A
motion.
DC 20V
Cut the sides of the hedge fi rst, then the top.
To cut the sides straightly, we recommend
1100 spm
cutting from bottom to top in the direction of
450 mm(18")
growth. Younger stems tend to move out-
wards when cutting them from top to bottom,
2.25 kg
resulting in shallow patches or holes in the
hedge.
1pc
To reach a level fi nish, fasten a piece of string
1pc
along the length of the hedge at the required
1pc
height and use as an alignment guide. Cut the
hedge just above the string.
Pay attention that no objects such as wires
are cut. The blade or drive can be damaged.
Maintenance and Service
Maintenance and Cleaning
► Pull the plug out of the socket before
► To ensure safe and effi cient operation,
► Clean the motor housing regularly with
► Wipe the knives thoroughly after use.
► Make sure that no water gets into the
In order to avoid safety hazards, if the power
supply cord needs to be replaced, this must
be done by P.I.T. or by an after-sales service
centre that is authorised to repair P.I.T. power
tools.

Storage and transportation

Store the instrument in closed rooms with
natural ventilation in a package at an air
temperature from 0 ° C to + 50 ° C and an air
humidity of no more than 80%.
Products can be transported by any type of
closed transport in the manufacturer's pack-
aging or without it, while preserving the prod-
uct from mechanical damage, atmospheric
precipitation. Remove the accessory from the
power tool before transporting.
Dispose of waste
6
Cordless Hedge Trimmer
carrying out any work on the power
tool.
always keep the power tool and the
ventilation slots clean.
a damp cloth. Do not use abrasive or
solvent-based cleaners.
After cleaning the blades, apply a thin
coat of light machine oil to prevent cor-
rosion.
instrument.
Damaged power tools, batteries, acces-
sories and waste packaging materials
must be recycled and reused in an envi-