Summary of Contents for Deaf Bonce APOCALYPSE AAB-1200.2D
Page 1
TWO-CHANNEL AMPLIFIERS ДВУХКАНАЛЬНЫЕ УСИЛИТЕЛИ AAB-1200.2D AAB-1800.2D CLASS D HTTPS://ALPHARD.AUDIO...
Page 3
1. Before installing the amplifier disconnect the battery from the electrical system. 2. To connect the amplifier it is necessary to stretch the power cable from the location of the battery to the place of installation of the amplifier. Select the power cable with the appropriate regulations in AWG (see Table: Selection of the diameter of the power cables) 3.
Page 4
5 . W I R I N G D I A G R A M S Connect the speaker cables from the positive and negative terminals of the speakers to the respective outputs of the amplifier terminal marked with CH1 / CH2 SPEAKERS OUTPUTS, as shown at the diagram. To connect the power wire supply it is necessary to use special power cables.
Page 5
Standard wiring diagram of two-channel amplifier to one subwoofer Step 1. Connect the speaker cable from (+) terminal of the amplifier to (+) terminal of the subwoofer. Step 2. Connect the speaker cable from (-) terminal of the amplifier to (-) terminal of the subwoofer. min.
Page 6
7 8 9 1 2 3 1. INPUT – signal input, RCA jacks 2. CROSSOVER – HPF – High pass filter (15 Hz –1 kHz at 12 dB/Oct) R e m o t e c o n t r o l 3.
Page 11
11.1 x 9.72 х 2.89 *RMS Power at 14.4 V, THD 1% Deaf Bonce amplifiers are high-quality and technically perfect products. The problems often arise due to improper use, faulty connection of components or lack of power supply of the on-board network.
Page 12
1 0 . W A R R A N T Y A N D M A I N T E N A N C E I N F O Deaf Bonce products are warranted against defects concerning materials and their manufacturing under normal functioning conditions.
Page 15
9. После завершения установки проверьте электропроводку системы и убедитесь в том, что все подключения были выполнены правильно. Перед установкой предохранителя, отключите плюсовой кабель от АКБ, установите предохранитель в держатель предохранителя. При помощи лампочки 12 В 21 Вт подключите плюсовой кабель к одному контакту лампочки, а...
Page 16
Шаг 1. Подключите акустический кабель от (+) клеммы усилителя к (+) клемме сабвуфера. Шаг 2 . Подключите акустический кабель от (-) клеммы усилителя к (-) клемме сабвуфера. мин. 2 Ом Внимание!!! Минимально допустимое сопротивление для мостового включения - 2 Ом. Для...
Page 17
7 8 9 1 2 3 1. INPUT – RCA разъемы для подключения низкоуровневых источников сигнала, линейные входы RCA R e m o t e c o n t r o l 2. CROSSOVER – HPF – фильтр высоких частот (15 Гц – 1 кГц при 12 дБ/Окт) 3.
Page 22
Модель AAB-1200.2D AAB-1800.2D Мощность RMS 4 Ом* (Вт) 580 x 2 670 x 2 Мощность RMS 2 Ом* (Вт) 780 x 2 1 020 x 2 Мощность RMS 1 Ом* (Вт) 1 210 x 2 1 800 x 2 Мощность RMS 4 Ом мостовое включение* (Вт) 1 560 х...
Need help?
Do you have a question about the APOCALYPSE AAB-1200.2D and is the answer not in the manual?
Questions and answers