Ingersoll-Rand FALCON F-17-V Installation Instructions Manual

5
REVERSING INSTRUCTIONS
TO REVERSE THE HANDING OF AN (F)17-V DEVICE
1) REMOVE CHASSIS COVER AND FOUR SCREWS (NOT SHOWN).
A
2) REMOVE COVER PLATE (4 SCREWS NOT SHOWN).
B C
3) REMOVE MAIN CAM AND TRIM CAM . NOTE: DO NOT REMOVE SLIDEBAR
B C
4) PLACE MAIN CAM AND TRIM CAM IN CORRECT LOCATION FOR APPOPRIATE HANDING AS SHOWN IN
FIGURE 1 OR 2.
E
5) REMOVE SPACER (1 SCREW, NOT SHOWN) AND PLACE IN OPPOSITE END OF SLIDEBAR
A
6) REASSEMBLE COVER PLATE (4 SCREWS NOT SHOWN).
7) PROCEED WITH INSTALLATION.
FIGURE 1
(RHR)
FRONT VIEW OF DEVICE
D
.
D
PER FIGURE 1 OR 2.
FIGURE 2
(LHR)
PAGE 16
D-1128
F-17-V & 17-V
EXIT DEVICES
INSTALLATION INSTRUCTIONS
1
PARTS CHECK
1) MAKE SURE THE CORRECT DEVICE IS BEING USED, AND IS THE CORRECT HANDING (SEE PAGE #16 FOR REVERSING
INSTRUCTIONS).
2) MAKE SURE ALL NEEDED PARTS ARE ON HAND.
NOTE: LIST DOES NOT REFLECT ALL POSSIBLE APPLICATIONS.
4) SCREW PACK FOR PANIC DEVICE
1) (F) 17-V DEVICE
DOGGING KEY (1 QTY.)
MOUNTING BRACKET
(1 QTY.)
SEX BOLT – 1/4"-20 THREAD
NOTE: DEVICE IS FIELD REVERSIBLE
(1 QTY.)
2) STRIKE
1/4" - 20 x 3/4" TPHMS (1 QTY.)
#10 x 1-1/4" FPHSMS
(6 QTY. (2 FINISHED))
4163/3788 2130
#10 x 1-1/4" PPHSMS (4 QTY.)
#14x1" PPHSMS (2 QTY.)
1/8" x 1" COTTER KEY (1 QTY)
2126A 4155
ROD GUIDE (2 QTY.)
(F)17-V
FIRE TOP 3788
ROD GUIDE INSERT (2 QTY)
BOTTOM 2130
PANIC TOP 4163
BOTTOM 2130
ROD GUIDE BRACKET (2 QTY)
OPT. BOTTOM 4155
OPT. BOTTOM 2126A
CHANNEL END CAP (1 QTY)
3) LATCHES & BOTTOM BOLTS
#10-24x3/8" PPHMS w/NYLON
PATCH (2 FINISHED)
#8-32x1/4" UFPHMS (4 FINISHED)
6) VERTICAL RODS (LENGTHS FOR 7'0" OPENINGS)
TOP LATCH BOTTOM
LATCH
3) MAKE SURE OUTSIDE TRIM (IF BEING USED) HAS BEEN PROVIDED AND IS THE CORRECT HANDING.
D-1128-a Copyright © 2008 Ingersoll-Rand Company Limited
5) SCREW PACK FOR FIRE DEVICE
MOUNTING BRACKET
(1 QTY.)
SEX BOLT – 1/4"-20 THREAD
(1 QTY.)
1/4" - 20 x 3/4" TPHMS (1 QTY.)
#10-24x3/4" FPHMS (6 QTY.)
#10-24x3/4" PPHMS (4 QTY.)
1/4"-20x3/4" PPHMS (2 QTY.)
1/8" x 1" COTTER KEY (1 QTY)
ROD GUIDE (2 QTY.)
ROD GUIDE INSERT (2 QTY)
ROD GUIDE BRACKET (2 QTY)
CHANNEL END CAP (1 QTY)
#10-24x3/8" PPHMS w/NYLON
PATCH (2 FINISHED)
#8-32x1/4" UFPHMS (4 FINISHED)
TOP ROD= 36"
BOTTOM ROD = 37-1/4" (WITH DEAD BOLT)