Table of Contents
Advertisement
Quick Links
Diagram may show a different but similar model. Overall length and rafter spacing may differ.
©2008 ClearSpan™
All Rights Reserved. Reproduction
is prohibited without permission.
Revision date: 06.11.08
ClearSpan
Portable Freestanding Building
CLEARSPAN
GARAGES & STORAGE SHEDS
™
™
STK#
DIMENSIONS
PB00558R3S
14' W x 10' H x 24' L
PB00558R4S
14' W x 10' H x 24' L
PB00560R3S
14' W x 10' H x 28' L
PB00560R4S
14' W x 10' H x 28' L
1
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for ClearSpan PB00558R3S
Summary of Contents for ClearSpan PB00558R3S
- Page 1 Portable Freestanding Building Diagram may show a different but similar model. Overall length and rafter spacing may differ. STK# DIMENSIONS PB00558R3S 14' W x 10' H x 24' L PB00558R4S 14' W x 10' H x 24' L ©2008 ClearSpan™...
-
Page 2: Safety Precautions
• Never erect the structure under power lines. • Identify whether underground cables and pipes are Thank you for purchasing this ClearSpan™ shelter. When present before preparing the site or anchoring the properly assembled and maintained, this product will structure. -
Page 3: Assembly Procedure
These words and phrases are common to most joints and to fasten brackets to rafters. ClearSpan™ shelters and identify the different parts of the shelter. (Some are used in this document. Others may not apply to this particular shelter.) These terms describe the shipped parts and can also be found on the materials list/spec sheets included with the shipment. -
Page 4: Required Tools
CLEARSPAN GARAGES & STORAGE SHEDS ™ SPECIAL NOTE: Wheel Jack Mounting Board REQUIRED TOOLS These instructions describe installing a mounting board The following list identifies the main tools needed to on the inside of the frame. The mounting board runs from assemble the shelter. - Page 5 CLEARSPAN GARAGES & STORAGE SHEDS ™ The following graphics and photos will help you identify the different parts and show you how they are used. (All parts are not shown.) FA4482B QH1400 QH1061 Tek Screw Band Clamp Ratchet ATTENTION: Actual...
- Page 6 CLEARSPAN GARAGES & STORAGE SHEDS ™ Round Style Portable Freestanding Building OVERVIEW This section is an overview of the process for assembling your Round Style Portable Freestanding Building. For details, please see the Assembling the Round Style NOTE: Diagram shows a shelter with Portable Freestanding Building Components section.
-
Page 7: Rafter Assembly
CLEARSPAN GARAGES & STORAGE SHEDS ™ ASSEMBLING THE ROUND STYLE PORTABLE FREESTANDING BUILDING COMPONENTS NOTE: Assistance is required to assemble the shelter. RAFTER ASSEMBLY Gather the Parts: 1˝ • Round Raft Position #1 (Pipe #14R1301) Tek screw • Round Raft Position #2 (Pipe #14R1302) •... -
Page 8: Frame Assembly
Check that the rafter is standing up straight (plumb). Position the bolt side of end clamp to the inside of the frame. SKU # Rafter Spacing center-to-center PB00558R3S 36" PB00558R4S 48" PB00560R3S 37-5/16"... - Page 9 CLEARSPAN GARAGES & STORAGE SHEDS ™ FRAME ASSEMBLY (CONTINUED) MOUNTING BOARD INSTALLATION 10. Continue adding rafters and purlins until the frame is The mounting board is supplied by the customer. For this assembled. (Remember to slide a band clamp onto...
-
Page 10: Strut Assembly
CLEARSPAN GARAGES & STORAGE SHEDS ™ MOUNTING BOARD INSTALLATION (continued) STRUT ASSEMBLY After the rafter assembly is complete and the mounting 3. Secure the mounting boards to the interior rafters using boards are attached, verify that the band clamps are in the two (2) U-bolts, four (4) nuts and washers. - Page 11 CLEARSPAN GARAGES & STORAGE SHEDS ™ FINISH ROUGH EDGES INSTALL PIVOT WHEEL ASSEMBLY Gather the parts: When the wheel pivot wheel assembly is properly installed and locked in the down position, the frame assembly will be • Duct tape (supplied by customer) off the ground.
- Page 12 CLEARSPAN GARAGES & STORAGE SHEDS ™ 2. Assemble two cover conduits. Start each conduit PREPARE MAIN COVER assembly with one plain pipe and add 75" swaged Gather the parts: pipes to arrive at the correct length. Secure each pipe joint with a Tek screw and wrap each joint using •...
- Page 13 CLEARSPAN GARAGES & STORAGE SHEDS ™ ATTACH MAIN COVER 4. Once the main cover is pulled into position, center the cover on the frame and remove the ropes. Loosely Gather the parts: secure the ends of the cover to the ratchets attached to the front and back end rafters.
- Page 14 CLEARSPAN GARAGES & STORAGE SHEDS ™ ATTACH MAIN COVER (CONTINUED) 12. Repeat the steps for the remaining ratchet or ratchets. 8. Repeat the steps for the remaining D-ring straps. 13. Using additional help (if needed) tighten the main cover beginning with the ratchets along the side of the shelter NOTE: All D-ring straps are attached to one side of frame.
- Page 15 If the shelter is moved, inspect all parts and connections before reassembling. • For replacement or missing parts, call 1-800-245-9881 for assistance. NOTE: With the exception of Truss Arch buildings, ClearSpan™ shelters and greenhouses do not have any tested loading criteria. Revision date: 06.11.08...
- Page 16 CLEARSPAN GARAGES & STORAGE SHEDS ™ QUICK START GUIDE 14' Wide Round Style Portable Freestanding Building Frame shown may differ in length and rafter spacing from actual frame. Revision date: 06.11.08...
- Page 17 CLEARSPAN GARAGES & STORAGE SHEDS ™ Revision date: 06.11.08...
- Page 18 CLEARSPAN GARAGES & STORAGE SHEDS ™ Revision date: 06.11.08...
- Page 19 CLEARSPAN GARAGES & STORAGE SHEDS ™ Revision date: 06.11.08...
- Page 20 CLEARSPAN GARAGES & STORAGE SHEDS ™ Revision date: 06.11.08...
- Page 21 CLEARSPAN GARAGES & STORAGE SHEDS ™ Revision date: 06.11.08...
- Page 22 CLEARSPAN GARAGES & STORAGE SHEDS ™ Revision date: 06.11.08...
- Page 23 CLEARSPAN GARAGES & STORAGE SHEDS ™ Revision date: 06.11.08...
Need help?
Do you have a question about the PB00558R3S and is the answer not in the manual?
Questions and answers