Table of Contents
Advertisement
Quick Links
Poly Shelters
TM
© 2004 ClearSpan
All rights reserved. Reproduction prohibited without written permission.
Rev: 16 July 04
Note: Photo may be of a different but similar model
Connect-A-Canopy Commercial Canopies
Instruction Manual
SKU #3620CC: 36' Wide x 20' Long
SKU #3630CC: 36' Wide x 30' Long
SKU #3640CC: 36' Wide x 40' Long
SKU #3650CC: 36' Wide x 50' Long
SKU #3660CC: 36' Wide x 60' Long
SKU #5420CC: 54' Wide x 20' Long
SKU #5430CC: 54' Wide x 30' Long
SKU #5440CC: 54' Wide x 40' Long
SKU #5450CC: 54' Wide x 50' Long
SKU #5460CC: 54' Wide x 60' Long
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for ClearSpan 3620CC
Summary of Contents for ClearSpan 3620CC
- Page 1 Note: Photo may be of a different but similar model Instruction Manual Connect-A-Canopy Commercial Canopies SKU #3620CC: 36' Wide x 20' Long SKU #3630CC: 36' Wide x 30' Long SKU #3640CC: 36' Wide x 40' Long SKU #3650CC: 36' Wide x 50' Long...
-
Page 2: A Word About Safety
Introduction Thank you for purchasing the ClearSpan Poly Shelter. We appreciate your patronage. We hope you enjoy building and utilizing your shelter. Please read this entire instruction manual before starting to assemble your shelter. If you require assistance during the construction process you may call us at 1-888-603-4445. -
Page 3: Selecting A Location
IMPORTANT - Read Anchoring Instructions You must read the anchoring instructions packed with your kit prior to shelter assembly! Selecting a Location It is important to select a proper location for your poly shelter. While the location may have been predetermined before you even ordered your shelter, you may want to “improve”... -
Page 4: Parts Identification
Parts Identification Driver Tek Screw Plain End Strap 4-Way Coupler 3-Way Coupler Strap Ratchet Cross Connector Rafter Section "A" Conduit (only swaged is shown) “Y” Post Cover Note: Illustrations are not to scale. Page 4... -
Page 5: Section B - Rafter Assembly
Section B - Rafter Assembly Step 1: Locate the 8 sections of pipe to make an end rafter. This will include (2) leg extensions, (2) legs, (2) rafter sections "A", and (2) rafter sections "B", Also locate a 3-way coupler and (2) cross connectors. -
Page 6: Section C - Rafter Setup
Section C - Rafter Setup Step 1: Stand up one of your end rafters (one of those with a 3-way connector). Secure it to an existing structure if possible so that it is plumb. If you donʼt have an existing structure, you can use some 2x4s tied with rope as shown below. -
Page 7: Section D - Installl Additional Bays
Step 6: Check the rafter-to-rafter dimensions along all the purlins. Also check that every rafter is standing up straight (plumb). Square the corners by measuring diagonally corner-to-corner, and line up all rafters using a straight line. Section D - Installl Additional Bays Step 1: Once you have the first bay installed and anchored, you can attach the second and any additional bays one at a time, a rafter at a time. -
Page 8: Section F - Install The Cover
Section F - Install the Cover Step 1: Unpack cover and unfold it completely with the inside surface facing up. Tip: The ends with black straps in the hems correspond to the front and back of the shelter. Step 2: Assemble (2) cover conduits each the length of your shelter using several 75" swaged sections and (1) 25", 49", or 73"... - Page 9 Step 5: Throw the ropes up and over the frame and then pull the cover over the frame. You need one person at each rope for this step. Step 6: Center the cover front to back and side to side. Step 7: In the front and rear hems, locate the black straps.
- Page 10 Step 12: Along both sides of the shelter, fasten ratchets to the sides of the legs identified in the previous step. Use a Tek screw in the bottom hole of the ratchet as shown below. Fasten the ratchet to the post below the "Y" section. There should be a few inches between the cover conduit and the ratchet.
-
Page 11: Section G - Shelter Maintenance
• Check connections and fasteners for tightness; replace and/or repair missing or damaged parts. • Contact ClearSpan for assistance in identifying needed parts; call us toll-free at 1-888-603-4445. • If shelter is moved after construction, inspect shelter thoroughly before reuse.
Need help?
Do you have a question about the 3620CC and is the answer not in the manual?
Questions and answers