Advertisement
Grow Wall3C
Thank you for purchasing OPCOM Farm Grow Wall 3C, the indoor hydroponics growing system. lt is designed for easy to use and
efficient growth by one-touch AUTO mode.lt holds up to 144 plants capacity. Please read the quick guide carefully before setting it up.
For detailed user guide video, please visit Grow Wall 3C page at http://www.opcomfarm.com
A. Assembly
A1. Remove all the parts from box and check all the accessories
Fan socket
Assembly
fan beam
Layer 4
LED
sockets
Control Box x 1pc
R3
column
Control
box
socket
L4 planting groove
Layer 3
LED
sockets
LED Growth Light x4pcs
Grow Kits
L3 planting groove
R2
Layer 2
LED
column
sockets
Seedling Tray x2pcs
(665*175*65mm)
L2 planting groove
Layer 1
Accessories
LED
sockets
Motor
socket
R1
L1 planting groove
column
Water tank
15
A2. Assemble GrowWall3
Assemble and secure the cross beam of the top fan and R3 colume with
1
screws.
Lift the wooden lid on top the fan's crossbeam. Plug the fan's power into
2
the fan socket, the first slot of the power socket cable, then close the lid.
Assemble the R3 column and the R2 column.
3
Hang the L4 planting groove and L3 planting groove on the columns
4
through the holes on the side planting grooves.Once hanged, set and
secure the clip onto the mechanism
Assemble the R2 column and the R1 column.
5
Assemble the L2 planting groove and the L1 planting groove on
6
the column.(see step.4)
Fix the power socket cable into the line groove in the column.
7
Stick the maple planks on the exterior of the assembled columns.
8
9.Set the LED grow light on the rocker arm on each layer of
9
columns. To set up, unscrew the thumb screw on the side of the
LED grow lights, remove the two circular spacers.
Place one spacer between the tip of the rocker arm and the side of the
LED grow light. Place another spacer between the thumb screw and the
tip of the rocker arm.
Once done, align the holes between each part and secure them with a
thumb screw.
Plug the power cord of the LED growth light into the LED socket of the
10
power socket cable on the column.
Organize the cables of the LED grow light and fix them in the line
groove on the rocker arm.
Dissembling the top and the bottom of the tube gives an aluminum
11
and a plastic tube.
Face the teeth of the aluminum tube downwards, then, from the interior
of the planting groove, work the tube through the holes on the bottom.
cover the tip of the aluminum tube in the planting groove with a filter
sponge.
Base Stand
Maple plank
Ribbon x10pcs
Hose x 1pc
Tube x4pcs
x2pcs
x2pcs
AC/DC adapder x 1pc
power cable x1pc
Warranty Card
Manual
Backup Pump x 1pc
Grow Sponge 60pk x9pcs
planting basket
Salt #1 (Nutrition)
Soda (pH+)
(OASP001)
50ml x1
(25mm) x150pcs
250ml x2
Alkaline
Neutral
Acidic
EC Meter
pH test
Water
Remote
x1pc
paper x1pc
Spray x1pc
Controller x 1pc
15
1
3
4
4
4
9
9
8
12
Set the water tank under the L1 planting groove.
12
Place the planting tray into the planting groove. Make sure
to correspond each water inlet of the planting tray to the
holes on the bottom of the planting groove.
Set the plastic tube in the water inlet of the planting tray.
13
Connect the tip of the aluminum tube at the bottom of the
planting groove by rotating.
Fill the water tank with 8gallons of water.
14
Plug the AC/DC adapter into a the power socket cable, then
15
connect the AC/DC adapter with the power cable to power
up the machine.
Draining Water Tank:
16
1. Open the water control box on the left side of the water tank by pulling
up the side planks. Take out the water drain pipe form the storing disk.
2.Prepare a water bucket with a capacity of around 40 L. Place the outlet of
thepipe un the bucket.
Turn On the pump and switch the water drain valve to Out to start draining.
3.Once finished draining, set everything back to default. (turn off the pump
and stop the water drain valve.)
Chart I: Control Box Mode
Remote Control
Power socket
Screw pack
cable x1pc
x1pc
Planting Tray(36 holes) x4pcs
Most plants can be grown using the AUTO mode.
Lemon(pH-)
B Scoop for Adjust
50ml x2
of Nutritio (5g)
Set up the Wake-up(automatically turns on everyday) and Sleeping(automatically turns off everyday) modes through lighting time setting.
A. When Power On, press hold POWER button until 2 beep sound (About 5 second) to reset power on timeline.
B. When Power Off, press hold POWER button until 2 beep sound (About 5 second) to reset power off timeline.
Fan follow LEDon / off.
Restore factory settings after power failure.
5. LED light planting mode Control
Cleaning
Filter
1.Select the mode of the LED grow light (you may switch between modes through the button on the
ponge x1pc
Sponge x5pcs
left side of the LED lamp holder).
2.The light comes with four modes: G(in green), S(in orange), L(in orange), and Off(colorless)(see
figure 1).
3.Please note that the remote control could only adjust the duration of lighting (On/ Hi /Low /Off),
as shown in chart 1. To switch between the mode of the LED grow light, please access the buttons on the light tubes manually.
4.Height of the LED grow light: Adjust the height and the angle of lighting manually through the rocker arm(see figure 2).
2
5.This hydroponics system comes with fans that improve the air circulation and accelerate the cooling of the LED tubes, which increases
the ventilation and avoids plants from overheating. Please make sure to keep a 5-10 cm distance between the light tube and the
plants to further prevent plants from overheating. To boost the light intensity in a power-saving way, direct the light at both the plant
11
11
and the wall simultaneously, which could add 30% more lighting to the plants.
Please read and follow every steps to avoid any malfunction.
B. Seedling
10
10
B1. Germination Stage
1. Add water to the seedling tray, up to the water (red) level.(Fig1)
10
10
2. First time sprout: just open the seedling box and add water. Then go to step 4. (Fig 1)
3. Second time sprout: Open Grow Sponge package,put each sponge piece into water of seedling tray
(make sure the front side with the seed label is side up), press the sponges into water 5 seconds and
7
ensure the sponges absorb water completely. Put seed moisturizing cover on the sponges.(Fig2)
4. Place the seedling tray with cover in the shade.(Fig3)
5. Suggest using Watering Spray water to sponges and keep them wet everyday.
13
6. During 0 ~ 7 days, find the sprouted ones in the tray; pick them out, and move them into product (make
sure the sponges lineup with the black dot on the partition)(Fig4) and to next stage: B2. Young Plant Stage.
7. Discard unsprouted sponges after regular germination time.
12
8. In each sponge, keep strong plants and cut the other weak plants.
* Different plant may have different germination time, please check before plant.
Chart II: Plant Stage
Basil, Lemon Balm
Germination Stage
Young Plant Stage
Growing Stage
* Please keep the seeds in refrigerator if you don't use it, recommended temperture is 41
* For your expected plant amount, you can refer to the sprout rate of 1st planting cycle.
* If you need more planting information, please vist to www.opcomfarm.com and read "Plant Q&A".
Grow Kits:
Status
Salt #1 (Nutrition)
Smart Control Box
Fuction
Status
Operation
Sound
On
One Press
BB
Power
Off
One Press
B 1sec
On
One Press
BB
Auto
Off
One Press
B 1sec
ON
One Press
BB
High
One Press
BBB
LED
Low
One Press
BBBB
OFF
One Press
B 1sec
ON
One Press
BB
High
One Press
BBB
Pump
Low
One Press
BBBB
OFF
One Press
B 1sec
Planting Time
LED Mode
Pump Mode
Nutrition
T
Day 0~7
68 - 77
-
-
-
Day 3~14
ON
ON
Need
59 - 86
After Day 14
Auto
Auto
Need
59 - 86
50.
-
B Scoop for Adjust of Nutritio (5g)
0.0-0.5
0.5-1.0
1.0-1.5
Add 2g
Add 1g
Standard range
16
Water Control Box
Water Cycling pipe
Water Cycling Valve
Water Drain Valve
Water Drain pipe
11 gallons
Pump
（40L）
Light
Time
On (Follow last mode before turn off)
Off
12Hr/day ON mode of LED and 30mins/ 2Hr ON mode of Pump
Follow LED and Pump manual mode seting
ON
HI
LOW
OFF
always On
ON
HI
LOW
OFF
18Hr/day
ON
HI
LOW
OFF
9Hr/day
ON
HI
LOW
OFF
always Off
ON
HI
LOW
OFF
55mins/ 1Hr
ON
HI
LOW
OFF
25mins/ 30mins
ON
HI
LOW
OFF
5mins/ 30mins
ON
HI
LOW
OFF
always Off
G mode
L mode
S mode
figure 1
Adjust the height of lighting
Adjust the angle of lighting
figure 2
(Fig1）
This side up!
(Fig2）
(Fig3)
(Fig4)
RH
EC
pH
Notes
( )
Be sure each sponge is fully wet in
80%
0.5-1.0
5.5-6.5
seedling tray.
45%-70%
1.0-2.0
5.5-6.5
45%-70%
1.0-2.0
5.5-6.5
over 2.0
Add water
Off
Advertisement
