Advertisement
Configuring an external A/V source in WinTV2000
using the optional A/V breakout cable
To bring video from an external audio/video source, you will
need an optional A/V cable set which is available from the
Hauppauge web store.
When using an external audio/video such as a satellite TV
receiver, VCR, cable TV set top box, camcorder, game con-
sole etc, you will need to connect the S-Video input con-
nector or Composite video input connector for video
and the Audio input (Line-In) for the sound.
To configure the external A/V source, in the WinTV2000
application click Menu / Suite Manager and Sources . To
add the S-video or Composite source, highlight the entry
and then select the Video Format from the drop down list.
NTSC is the commonly used format in North America.
Select Add to finish. Then click Close . To select an external
audio/video source, click the Up and Down channel but-
tons to cycle through TV, Composite and S-Video sources.
The external source is at the end of the channel list.
Watch and record TV
One Touch Pause
One Touch Record
TV Modus
Pause
Record
There are two buttons to control the Watching and
Recording of TV. Clicking on the Record button will cause
the Record menu to roll down. Clicking OTR will cause the
Record menu to roll down, and start recording.
Note: Pause is not supported on WinTV-HVR-950.
Recording TV with the WinTV-HVR-950
When recording ATSC digital TV, the recording format is
the same as the digital TV resolution of the TV program.
These recordings will consume a large amount of hard disk
space. For example, if the TV program is being transmitted
at the highest ATSC resolution, called "1080i', the recording
will consume 5.6 Gigabytes of disk space per hour of
recording.
When recording
analog cable TV
using SoftPVR, the
'DVD' MPEG-2 for-
mat will typically
consume 2.8 Gbytes
per hour.
Page 7
WinTV Scheduler works by using the Windows Task
Scheduler to launch WinTV at the chosen time. WinTV
Scheduler sets up a command line in Task Scheduler to run
WinTV2000, specifying a TV channel and a length of time to
record.
To set up an event for timed watching or recording, run
Scheduler and click on the Add Program . The items that
need to be set for each event are:
- Time to Begin Program: set to the desired start time.
The default time is about 3 minutes from the current time.
Click on the hour to set the hour, the minute to set the
minute and the second (if you feel this is necessary) to
set the second to start the program.
N
ote: It takes about 10 seconds to launch the WinTV and set up for
recording.
- Time to End Program: set to the time to end this event.
N
ote: you need to leave at least 30 seconds between scheduled pro-
grams to give the recorder time to set up its disk buffers.
- Program Period: one time, daily, weekly
- Date to Begin Program: today's date is the default.
Change this if you want to schedule on another date.
- Source selection: leave at WinTV2000 to open WinTV at
the requested time and the requested channel.
- Channel selection: choose one of the scanned channels.
- Recording options: click on Record to File to record
your show. Leave this button unchecked to watch TV at
the requested time. You can also name your file to record.
Once these are set, click Set Program . You can add more
Events, clicking Set Program after each event is set. When
you are finished click Close . The WinTV program does not
have to be running for the Schedular to work. If WinTV is
not running, it takes about 10 seconds to start Scheduler
and to start the recording of TV.
Keyboard shortcuts
Sound up
- Page Up
Ctrl+M
Sound down
- Page Down
ALT+M
Plus (+)
- Chanel Up
0-9
Minus (-)
- Channel Down
F1
Ctrl T
- Frame TV
SHIFT+F1 - Online Help
Space bar - Take a Snapshot
Ctrl P
- Frame Print
Ctrl F
- Still image
Page 10
Record mode
Skip back 10 sec
Skip back 10 sec
Configuring the record formats
When recording analog TV, WinTV2000 uses your PC or
laptops processor and Hauppauge's SoftPVR to make
the recording. The default recording quality is DVD. To con-
figure the directory to store video recordings and to check
the analog recording format, click the Pref button and then
Movies .
Note: since ATSC digital recording uses the format the orig-
inal TV program is broadcast in, there are no other record-
ing format options.
To record TV
Click on the Record button or the OTR button on the
WinTV-2000 application to open the Record and Playback
control bar.
Time counter
Hour:Minute:Second format.
Record
matically generate a file name and start recording your
audio/video program.
Stop
you are recording or playing back.
Play
disk the last video file created. When playing a video, you
can rewind, fast forward, replay 10 sec or skip forward 10
sec using the buttons on the control bar.
Pause Clicking the Pause button while Playing will
pause your audio/video.
Rewind button Clicking the Rewind button will play
the video file in reverse. Clicking the Rewind button again
will continue the playing of the video.
Fast forward button Clicking the Fast Forward but-
ton one time will fast forward your video at 2X speed.
Clicking the Fast Forward button two times will fast forward
your video at 8X speed. Clicking the button again will con-
tinue playing back at normal speed.
Troubleshooting
N
ote: the latest WinTV-HVR-950 software can be found at
www.hauppauge.com/pages/support/support_hvr950.htm
Some notes on system compatibility
Decoding high definition ATSC TV is very CPU intensive. A
graphics card with at least 64MBytes of memory and the
latest graphics driver from the manufacturer makes the
decoding task easier. Typically a 2.2 GHz Pentium 4 proces-
sor or equivalent with a graphics card having 64MBytes of
memory is required to properly decode ATSC digital TV on
your PC. A 1.6GHz AMD Sempro laptop computer tested in
the Hauppauge lab used 50% of the CPU for playing ATSC
640i format, and 90% of the CPU when playing ATSC 1080i,
the highest definition ATSC format.
In some cases, either a faster processor or more graphics
memory might be required. Slow or jerky video and a noisy
TV picture indicate system performance problems.
Jerky video with live ATSC digital TV
Jerky or distorted video can be caused by two things in
your PC or laptop: a slow CPU which cannot decode the
ATSC TV signal fast enough, and a graphics system which
cannot keep up with the high datarates of ATSC TV.
Many times, improving the performance of the graphics dis-
play will fix the jerky video display of ATSC digital TV. Here
are some tips on improving graphics performance:
- Use the latest graphics driver: graphics drivers are
often 'tweaked' to improve performance, especially the
built-in graphics on laptops. Check the Microsoft Windows
update site to download the latest graphics driver for your
computer. For Dell computers, check the Dell website for
the latest graphics driver.
- Use Hauppauge's Primary program to optimize
graphics performance: Primary.exe is used to change
the display mode of a graphics card for TV watching. This
does not affect any other Windows program. Primary.exe is
found in the Hauppauge WinTV program group. The default
mode used by WinTV2000 is
Force Primary. Force
Primary uses your processor
- Mute on/off
to move the digital TV image
- Re-size TV menu
into the graphics memory. It is
more CPU intensive but often
- Channel number
fixes display problems on some
- Launch Help
laptops. Note: Snapshot
does not work in 'Force
Primary' mode.
To use hardware graphics
Time counter
Video-position
Skip forward 10 sec
Skip to end
File menu (save / open)
Record
Pause Stop
Play
Fast forward
Fast rewind
Slow motion
- the time is specified in a
Clicking the Record button will auto-
Clicking the Stop button will stop the video
Clicking the Play button will playback from
Page 8
Page 11
Slow motion button
Clicking the Slow Motion
button during playback will cause the video to play in slow
motion. Clicking the Slow Motion button again will return
the video to normal playback speed.
File button
Clicking the File button opens the File
menu. The last file recorded is listed in the File name box.
In the File menu you can:
Rename your recorded video file: To rename a video
●
file, find the file you would like to rename, highlight it with
your mouse, and click and hold the right mouse button.
Go down to Rename and then you can type in a new
name. Remember:you must keep the MPG extension on
the file.
Play a video file previously recorded: Find the file you
●
would like to play, highlight it with your mouse (one click
of the mouse button) and click Open. Then click the Play
button.
Delete recorded video files which you no longer
●
want: Click your right mouse button on the video file
once, go down the menu and click Delete .
Schedule TV recordings with WinTV-
Scheduler
WinTV Scheduler allows you to schedule the recording of
TV shows. WinTV Scheduler, once it is set, can be closed,
and the WinTV application will "wake up" at the desired
time and tuned to the desired channel.
When using an Electronic Program Guide (EPG) such as
TitanTV, the
WinTV
Scheduler
makes a con-
version so that
correct ATSC
digital chan-
nels will tuned.
For example, if
the EPG wants
to record digi-
tal channel
22.2, you will
see the record-
ing listed in
WinTV
Schedule as recording channel 1222.
After installation, WinTV Scheduler can be found on your
Windows desktop. You can also find it in Start / Program
files / Hauppauge WinTV.
Page 9
acceleration, close WinTV2000, then run Primary. Click
Allow VMR . Close Primary and rerun WinTV. The Allow
VMR setting will allow your graphics system to use hard-
ware acceleration for video decode. Note: graphics hard-
ware acceleration does not work on all systems.
If this setting does not help, or if you experience WinTV not
responding after a channel change, then your graphics sys-
tem cannot use hardware graphics acceleration.
In this case, run Primary. Click ' Force Primary ' then rerun
WinTV.
Only some channels are found during ATSC
channel scan
If you are only receiving some known TV channels when
scanning, it means your TV antenna is not adequate to pick
up the channel. You will need either an antenna signal
booster (a Radio Shack antenna amplifier will work) or a
high gain antenna. Here's a link to an ATSC antenna selector:
http://www.antennaweb.org/aw/address.aspx
Black window when selecting an ATSC channel
A black window when selecting an ATSC channel means
that the WinTV-HVR-950 is not getting a signal. This is most
often due to poor reception. See "Only some channels are
found during ATSC channel scan" above.
Uninstalling the WinTV driver and applications
Run the hcwclear.exe from the installation CD. Select OK A
black screen will briefly appear and once it has disappeared
the software will be removed. If you now re-start the comput-
er you will be at Step 4 of the installation.
FCC Statement
Radio Interference Statement:
The WinTV products have been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a resi-
dential installation. This equipment generates, uses, and can radiate radio fre-
quency energy and cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or televi-
sion reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the follow-
ing measures: reorient or relocate the receiving antenna,increase the separation
between the equipment and receiver, connect the equipment into an outlet on a
circuit different from that to which the receiver is connected, consult the dealer or
an experienced radio/TV technician for help.
FCC ID: H90WINTV
CE Statement: This equipment has been tested and complies with EN 55013, EN
55020 and IEC 801-3 part 3 standards.
CAUTION: Changes or modifications not expressly approved by the party respon-
sible for compliance to the FCC Rules could void the user's authority to operate
the equipment.
Page 12
Advertisement
