Hauppauge WinTV-HD Quick Installation Manual

Hauppauge!
®
WinTV-HD
Quick Installation Guide
for Windows ® 98/Me/2000
Note: The WinTV-HD requires the latest version of Windows98, known as Windows98-SE,
any version of Windows2000 or WindowsMe.
Note: We recommend a PII 600 or better for recording transport streams to you hard disk.
Contents of the WinTV-HD package
WinTV-HD board
Pod Cable,
with A/V inputs, IR connection
and Monitor interface
External Audio cable - 1/8" miniplug to
1/8" miniplug.
S/PDIF cable , to convert LineOut jack to
Phono plug for S/PDIF Applications
This board and remote are subject to change
Internal Audio Connector, Connect
Analog Audio Internal to your sound card.
Wireless Remote with 2 AAA batteries.
Remote receiver with velcro fastener. Pod Cable
WinTV-HD for Windows Installation
CD-ROM
with:
Wireless
WinTV driver and application
Remote
Remote control application
Utilities
Remote
receiver (IR)
VGA to
Internal Audio
Y-Pr-Pb
Connector
Adapter
Step 1: Prepare the computer
Switch off the computer.
The manufacturer of your PC sup-
plies instructions on removing the
PC cover.
Remove the cover.
Step 2: Install the WinTV-HD board
Locate a free PCI slot (a short
white slot).
Unscrew and remove the metal
cover plate which covers the back
of the empty slot.
Plug the WinTV-HD board into the
PCI slot, and screw the WinTV's
metal cover plate to the PC.
Replace the computer cover.
Page 1
Step 3: Connect the WinTV-HD cables
The WinTV-HD board has two coax video Digital sound RCA jack
connectors: one for a UHF/VHF TV antenna
Plug the Pod Cables'
and one for cable TV . Screw your UHF/VHF
into the WinTV-HD Pod Cable connector
antenna (a rooftop antenna is recommended
for digital TV reception in most areas) into the
The yellow
Antenna connector . Plug your cable TV con-
connector
nection to the Cable TV connector .
Pod Cable can be used to input analog
audio/video from a VCR, camcorder, DVD
One end of the External Audio cable (1/8"
player or satellite TV receiver.
minijack) should be plugged into WinTV-HD's
Audio LineOutput, and the other end plugged
The Remote receiver (IR)
into the Line-In connector on your PC's
Pod Cable's (IR) plug
sound card for stereo speaker sound.
position the Remote Receiver (IR) where it
will be able to receive line of sight, infra-red
If you are connecting the WinTV-HD to a
commands from the Remote Transmitter.
Home Theater system which uses a Digital
sound input, the WinTV-HD's S/PDIF adapter
lets you convert the 1/8" Line-Out jack to a
(Pod) A/V Connectors
WinTV-HD
Connections
Antenna connector
Cable TV connector
Audio LineOutput
or S/PDIF S-Video In
VideoIn
Pod Cable connector
Remote
Receiver (IR
S/PDIF
Cable
Step 4: Using the S/PDIF & Internal Analog connectors
S/PDIF Jumper setting Internal Analog Audio Connector
When using the
To configure the WinTV-HD for an exter-
nal S/PDIF decoder, place the 2 Shunt your digital channels, audio from your analog TV
jumpers vertically on the top half of channels comes from the Internal Analog Audio
jumper JP4 . This routes the S/PDIF connector.
output to the Audio LineOutput mini
- Connect one end of the supplied internal
stereo connector. Then connect the
audio cable to connector
supplied S/PDIF cable between the
WinTV-HD
Audio Line-Out jack on the WinTV-HD
back panel connector and a Digital
- Connect the other end to your sound card's
input on your Home Theater sys-
black internal audio input connector.
tem .
Analog audio setting
S/PDIF audio setting
S/PDIF Shunt
JP4
JP4
Jumpers (JP4)
(Factory default)
Page 2
Step 5: Single and Dual Monitor Setup
Single Monitor mode (SMS)
. See Step 3a below.
In Single Monitor mode, you can watch analog
and digital TV-in-a-window plus see Hi-Def TV
26-pin male connector
full screen on your VGA monitor.
.
Remove your VGA monitor cable from your
VideoIn jack , the 4pin S-Video In
VGA card and connect it to the short leg of the
and the AudioIn (L) and (R) on the
Pod cable labeled "MONITOR".
Now, connect the long leg of the Pod cable
labeled "VGA" to your VGA card.
Dual Monitor mode (DMS)
is plugged into the
In Dual Monitor mode, you can watch analog
. Use the Velcro dot to
and digital TV-in-a-window on your VGA
screen, plus at the same time see Hi-Def TV
full screen on another Hi-Def monitor or anoth-
er VGA monitor. Connect your high definition
to VGA card
to VGA or HiDef
monitor
Step 6: Install the WinTV driver for Windows
AudioIn
(R)
AudioIn
(L)
)
5b. When you see the above dialog box, insert the
WinTV Windows Installation CD-ROM into your
for audio from
S/PDIF output
CD-ROM drive. Select CD-ROM drive and
click Next.
5d. You will see a number of files being copied to
your hard disk drive.
JP2 on the
Click . You will need to reboot your
5e. Finish
system for the changes to take effect.
5f.
Internal Analog
Audio connector
(JP2)
Step 7: WinTV Software installation
monitor to the short leg of the Pod cable
labeled "MONITOR" . Leave your VGA monitor
connected to your VGA card. During operation
you need to tell the software you are in DMS.
Right click the mouse button on the TV screen
and keep the right mouse button depressed
for a few seconds until you'll see the Settings
menu pop up. Then go to Hi-Def Options and
click Dual Monitor.
If you are using the supplied VGA to Y-Pr-Pb
, check as
adapter YPrPb Primary display
your Primary display.
You can choose the Hi-Def output resolution by
clicking one of the Set resolutions settings.
Step 8: The new WinTV2000 application
Volume Up
& Down
to the WinTV-HD
board
Color/audio
configuration
5a. When re-starting Windows for the first time
after the WinTV-HD board has been
installed, the Add New Hardware Wizard will
appear.
Click Next. Select Search for the best dri-
ver for your device Recommended Click
Next.
entry is set to Antenna
The WinTV-HD will be listed in Device Manager
in Sound Video and Game
controlers as Janus Video Capture
Page 3
After the PC reboots the WinTV Application
Setup will be run.
To use the remote control, make sure Install the
Hauppauge IR Remote Control Application is
checked.
Click Install to install the WinTV2000.
After the Setup program is complete, you will see
a WinTV2000 icon on your Windows desktop. To
run the WinTV2000 application, double click on
the WinTV2000 icon. After rebooting your PC,
the Remote Control will be enabled.
Preferences
menu
Full screen TV
Minimize
Channel Up & Channel Down
Remove toolbar
Close WinTV
Channel
configuration
Click your right mouse button
here to remove toolbars. Click
again to restore toolbars.
Freeze TV
Click and hold your right
mouse button to see the
Snapshot viewer window
Options menu.
Double click on each
"thumbnail" to see
image full size
Software remote
Snapshot button Current TV channel control & Video
or video source controls
Scanning for channels
When running WinTV2000 for the first time, you will
need to scan for your HDTV channels. The
board has two coax video connectors: a
WinTV-HD
UHF/VHF TV antenna connector and a cable TV connec-
tor. You will need to scan for TV channels on each con-
nector.
When scanning the UHF/VHF Antenna
Connector, set the Tuner Format to DTV-ATSC . Make
sure the Broadcast entry is set to Antenna.
When scanning the Cable Connector for HDTV channels,
set the Tuner Format to MN . Make sure the Broadcast
or to Cable for regular cable channels.
Setting up the channels
After you have scanned for channels, you can
add the channel names. To do this, click on the
Suite button on WinTV2000 .
Then double click on Input Sources.
Chose Tuner for the Antenna , or Tuner2 for
Cable TV
.
Click on the desired channel, then click on Edit .
Change the ChannelName to the name of the
station. Then click OK .
Page 4