Table of Contents
Advertisement
ADJUSTING THE AIR FLOW DIRECTION (see figure 6)
(only for FXYCP, FXYFP, FXYKP)
Press the air flow direction button to select the air direction.
1
The air flow flap display swings as shown below
and the air flow direction continuously varies.
(Automatic swing setting.)
Press the air flow direction adjust button to select
2
the air direction of your choice.
The air flow flap display stops swinging and the air
flow direction is fixed. (Fixed air flow direction
setting.)
MOVEMENT OF THE AIR FLOW FLAP (see figure 13)
For the following conditions, a micro computer controls the air flow
direction which may be different from the display.
COOLING
• When the room temperature is lower
than the set temperature
• When operating continuously at horizontal air flow direction
These conditions are also valid for automatic operation.
The air flow direction can be adjusted in one of the following ways.
•
The air flow flap itself adjusts its position.
•
The air flow direction can be fixed by the user.
•
Automatic
and desired position
Note
•
The movable limit of the flap is changeable. Contact your
Daikin dealer for details. (only for FXYCP, FXYFP, FXYKP)
•
Avoid operating in the horizontal direction
cause dew or dust to settle on the ceiling.
PROGRAMMING START AND STOP OF THE SYSTEM
WITH TIMER (see figure 9)
•
The timer is operated in the following two ways.
Programming the stop time
operating after the set time has elapsed.
Programming the start time
operating after the set time has elapsed.
•
The timer can be programmed for a maximum of 72
hours.
•
The start and the stop time can be simultaneously
programmed.
Press the timer mode start/stop button several times and
1
select the mode on the display.
The display flashes.
•
For setting the timer stop
•
For setting the timer start
Press the programming time button and set the time for
2
stopping or starting the system
Each time this button is pressed, the time advances
or goes backward by 1 hour.
Press the timer on/off button.
3
The timer setting procedure ends. The display
changes from flashing light to constant light.
HEATING
• When the room temperature is lower
than the set temperature
• At defrost operation
.
. It may
. The system stops
. The system starts
or
Note
•
When setting the timer off and on at the same time,
repeat the above procedure (from
again.
•
After the timer is programmed, the display shows the
remaining time.
•
Press the timer on/off button once again to cancel
programming. The display vanishes.
For example: (see figure 11)
When the timer is programmed to stop the system after 3
hours and start the system after 4 hours, the system will stop
after 3 hours and start 1 hour later.
SETTING THE MASTER REMOTE CONTROLLER (for
RSXYP and RSEYP series)(see figure 10)
•
When the system is installed as shown in figure 14 and 15, it is
necessary to designate one of the remote controllers as the
master remote controller.
FOR RSXYP SERIES (see figure 14)
When one outdoor unit is connected with several indoor units.
FOR RSEYP SERIES (see figure 15)
When one BS unit is connected with several indoor units.
•
Only the master remote controller can select heating, cooling or
automatic (only RSEYP series) operation.
•
The displays of slave remote controllers show
(changeover under control) and they automatically follow the
operation mode directed by the master remote controller.
However, it is possible to changeover to program dry with slave
remote controllers if the system is in cooling operation set by the
master remote controller.
How to designate the master remote controller
Press the operation mode selector button of the current
1
master remote controller for 4 seconds.
The display showing
all slave remote controllers connected to the same outdoor
unit or BS unit flash.
Press the operation mode selector button of the controller
2
that you wish to designate as the master remote controller.
Then designation is completed. This remote controller is
designated as the master remote controller and the display
showing
(changeover under control) vanishes.
The displays of other remote controllers show
(changeover under control).
PRECAUTIONS FOR GROUP CONTROL SYSTEM OR
TWO REMOTE CONTROLLER CONTROL SYSTEM
This system provides two other control systems beside individual
control (one remote controller controls one indoor unit) system.
Confirm the following if your unit is of the following control system
type.
•
Group control system
One remote controller controls up to 16 indoor units. All indoor
units are equally set.
•
Two remote controller control system
Two remote controllers control one indoor unit (in case of group
control system, one group of indoor units). The unit is
individually operated.
Note
•
Contact your Daikin dealer in case of changing the
combination or setting of group control and two remote
controller control systems.
to
) once
1
3
(changeover under control) of
4
Advertisement
Table of Contents
