Table of Contents
Advertisement
IMPORTANT!
v Dispose of the batteries through or via your municipal recycling
collection centre.
1. Discharge the lithium-ion cells completely
(contact the FLYMO Service).
2. Protect the contacts on the lithium-ion cells against short circuits.
3. Dispose of the lithium-ion cells properly.
6. TROUBLESHOOTING
DANGER! Risk of injury!
Cut injury when the product starts accidentally.
v Wait for the blade to stop, remove the battery, remove
the safety key and use gloves before you troubleshoot the
product.
To replace the blade [ Fig. T1 ]:
DANGER! Risk of injury!
Cut injury when the blade turns and it is damaged,
bent, out of balance or has chipped edges.
v Do not use the mower when the blade is damaged, bent,
out of balance or has chipped edges.
v Do not regrind the blade.
The FLYMO spare parts are available from your FLYMO dealer or from
the FLYMO service.
Only use an original FLYMO blade:
• FLYMO replacement blade for 300 Li: Art. FLY 069
• FLYMO replacement blade for 340 Li: Art. FLY 087
SimpliStore 300 Li [ Fig. T2 ]:
1. Ensure the lawnmower is stopped and disconnected. Insert a screw-
driver through the reinforced hole on the deck into the drive pulley
wheel to stop the wheel from turning during the blade change.
2. Unscrew the blade bolt. Take care not to damage the drive pulley wheel
when applying force.
3. Remove the blade bolt and the washer.
4. Remove the blade.
5. Put the new blade on the lawnmower.
6. Put the washer and the blade bolt on the lawnmower.
7. Screw the new blade tight with the blade bolt. Tightening torque is
15 – 20 Nm. Do not over-torque.
Take care not to damage the drive pulley wheel when applying force.
8. Ensure the screwdriver is removed before attempting to turn on the
machine.
SimpliStore 340 Li [ Fig. T3 ]:
1. Ensure the lawnmower is stopped and disconnected. Insert a screw-
driver through one of the holes in the spacer into the reinforced hole on
the deck to stop the axle from turning.
2. Unscrew the blade bolt. Take care not to damage the spacer when
applying force.
3. Remove the blade bolt and the washer.
4. Remove the blade.
5. Put the new blade on the lawnmower.
6. Put the washer and the blade bolt on the lawnmower.
7. Screw the new blade tight with the blade bolt. Tightening torque is
15 – 20 Nm. Do not over-torque.
Take care not to damage the spacer when applying force.
8. Ensure the screwdriver is removed before attempting to turn on the
machine.
Problem
Possible Cause
Mower does not start
Safety key is not in position I.
Battery is not put completely
into the battery holder.
22301-85.960.01.indd 7
22301-85.960.01.indd 7
Problem
Mower does not start
Engine is jammed and
makes a noise
Loud noises, the mower
is rattling
Mower runs unevenly or
vibrates strongly
Lawn is not cleanly mowed
Red Error-LED on the battery
illuminates
After pushing the button
no LED on the battery
illuminates
After pushing the button
the LED on the battery
flashes red.
Charging control lamp
on the charger does not
illuminate
Charging control lamp on
the charger illuminates red
Charging control lamp on
the charger flashes red
7. TECHNICAL DATA
Battery Lawnmower
Speed of rotation cutting
blade
Cutting width
Cutting height adjustment
Volume of grass box
Weight (without Battery)
Sound pressure level L
Uncertainty k
Sound power level L
measured / guaranteed
Uncertainty k
Hand / arm vibration a
Measuring process complying with:
sure. The vibration emission value can vary during actual use of the electric power tool.
Battery B16-2025A
Battery voltage
Battery capacity
Number of cells (Li-Ion)
Remedy
Battery charging time
v Turn the safety key to
(approx.)
position I.
Lawn area per battery
v Put the battery completely
charge (approx.)
into the battery holder until
it audibly engages.
Appropriate FLYMO System Batteries B16-2025A: Art. 967913201
Possible Cause
Battery is empty.
Motor is blocked.
Motor is blocked.
Cutting height is too low.
Screws on engine, its fixing
or on the mower chasing are
loose.
Blade is damaged / worn or the
blade mounting is released.
Blade is very dirty.
Blade is blunt or damaged.
Cutting height is too low.
Battery temperature is out
of range.
Battery is defective.
Battery temperature is out
of range.
Battery charger or charging
cable are not connected
correctly.
Battery temperature is out
of range.
Battery error / battery defective. v If the battery cannot be
NOTE: For any other malfunctions please contact the FLYMO Customer Service.
Repairs must only be done by FLYMO service departments or specialist dealers
approved by FLYMO.
Unit
Value
SimpliStore 300 Li
9705395-xx
R/min
3500
cm
30
25 – 65
mm
(3 positions)
l
30
kg
8.0
88.4
1)
dB (A)
pA
3.0
pA
:
2)
WA
88 / 89
dB (A)
1.0
WA
1)
m/s
< 2.5
2
vhw
EN 60335-2-77
RL 2000/14/EC / S.I. 2001 No.1701
1)
2)
NOTE: The stated vibration emission value has been measured according to
a standardized test procedure and can be used for comparison of one electric
power tool with another. It can also be used for preliminary evaluation of expo-
Unit
Value (Art. 967913201)
V (DC)
20
Ah
2,5
5
min.
120
m
250
2
Remedy
v Charge the battery.
v Remove the obstacle.
Start again.
v Remove the obstacle.
Start again.
v Raise the cutting height.
v Let the screws be tightened
by an authorised specialist
dealer or the FLYMO Service.
v Replace the blade.
v Clean the blade.
v Replace the blade.
v Raise the cutting height.
v Use the battery in surround-
ings where temperatures are
between 0 °C and 40 °C.
v Replace the battery.
v Use the battery in surround-
ings where temperatures are
between 0 °C and 40 °C.
v Connect the battery charger
and charging cable correctly.
v Use the battery in surround-
ings where temperatures are
between 0 °C and 40 °C.
reset by connecting it to
the charger, contact the
FLYMO Service.
Value
SimpliStore 340 Li
9705396-xx
3300
34
20 – 60
(5 positions)
35
10.4
82.7
3.0
86 / 87
1.0
< 2.5
7
25.10.21 14:12
25.10.21 14:12
Advertisement
Table of Contents
