Operation Position; Maintenance; Troubleshooting - Flymo SimpliGlide 300 Operator's Manual

Operation position:

Adjustment is not required to move the handle to the operating position.
Simply pull down from the forward position or lift up from the down
position until the handle is in the most comfortable operating position.
To start the mower [ Fig. O6 / O7 ]:
DANGER! Risk of injury!
Risk of injury if the product does not stop when you
release the start levers.
v Do not bypass the safety devices or switches. For example do
not attach the start levers to the handle.
To start:
The product is provided with a two-handed safety device (start
lever (18) and safety lock-off button
being turned on by accident.
(18)
There are two start levers
1. Push the safety lock-off button
(18)
lever with the other hand.
The mower starts.
2. Release the safety lock-off button
To prevent a ring being cut in the lawn and to clear any residual grass,
tilt the mower slightly. When the lawnmower has reached full speed gently
lower it onto the lawn.
To stop:
(18)
v Release the start lever .
The mower stops.
Tips to use the mower [ Fig. O8 ]:
Mow twice a week during the growing season.
The lawn will suffer if more than a third of its length is cut at one time.
For the best results mow the outside edge of the lawn in a clockwise
direction first.
Start to mow the edge of the lawn nearest to the power point.
So the cable is laid out on the lawn you have already cut.
For the best cutting results mow in straight lines with an overlap of
approximately 8 – 10 cm on each pass with the mower.
Do not overload the mower. To mow long thick grass may cause the
motor speed to drop and you will hear a change in the motor sound.
If the motor speed drops you may overload the mower which may cause
damage. When you mow in long thick grass a first cut with the cutting
height set higher will help reduce the load.
See To adjust the cutting height.

4. MAINTENANCE

DANGER! Risk of injury!
Cut injury when the product starts accidentally.
v Wait for the blade to stop, disconnect the product from the
mains and use gloves before you maintain the product.
To clean the mower:
DANGER! Risk of injury!
Risk of injury and risk of damage to the product.
v Do not clean the product with water or with a water jet
(in particular high-pressure water jet).
v Do not clean with chemicals including petrol or solvents.
Some can destroy critical plastic parts.
The airflow slots must always be clean.
To clean the underside of the mower [ Fig. M1 ]:
The underside is easiest to clean after you mowed.
1. Lay the mower on its side carefully.
(19)
2. Clean the underside by removing any grass build up with the
spanner / scraper tool (17) .
(14)
3. Clean the blade and the fan
objects).
To clean the outside of the mower [ Fig. M2 ]:
1. Clean the outside with a dry cloth.
2. Clean the airflow slots (20)
6
SG300UK-20.960.01.indd 6
(5) ) to prevent the product from
fitted. Either one has to be used to start.
(5) with one hand and pull the start
(5)
.
(15)
with a soft brush (do not use sharp
with a soft brush (do not use sharp objects).
5. STORAGE
To put into storage:
The product must be stored away from children.
1. Disconnect the product from the mains.
2. Clean the mower (see 4. MAINTENANCE).
3. Store the mower in a dry, enclosed and frost-free place.
Storage positions [ Fig. S1 ]:
1. Push the lower handle (1) inwards from both sides simultaneously.
2. Rotate the handle (1) to the desired position, either forward for the folding
storage position or backward for the wall mounting storage position.
3. Loosen the handle knobs (6) and fold the upper handle
Make sure that the cable is not locked between the lower and the
upper handle.
Folding storage position [ Fig. S2 ]
Wall mounting storage position [ Fig. S3 ]:
NOTE: When wall-mounting storage, always hang the mower from
the lower handle (1) cross section.
Disposal:
(in accordance with RL2012/19/EC)
The product must not be disposed of to normal household
waste. It must be disposed of in line with local environmental
regulations.
IMPORTANT!
v Dispose of the product through or via your municipal recycling collection
centre.

6. TROUBLESHOOTING

DANGER! Risk of injury!
Cut injury when the product starts accidentally.
v Wait for the blade to stop, disconnect the product from the
mains and use gloves before you troubleshoot the product.
To replace the blade:
DANGER! Risk of injury!
Cut injury when the blade turns and it is damaged, bent,
out of balance or has chipped edges.
v Do not use the mower when the blade is damaged, bent,
out of balance or has chipped edges.
v Do not regrind the blade.
The FLYMO spare parts are available from your FLYMO dealer or from the
FLYMO service.
Only use an original FLYMO blade:
FLYMO Replacement Blade for 30 cm:
Reference no. FLY094
FLYMO Replacement Blade for 33 cm:
Reference no. FLY095
FLYMO Replacement Blade for 36 cm:
Reference no. FLY096
v Replace the blade (see 3. OPERATION To adjust the cutting height).
Problem Possible Cause
Mower does not start
Mains cable is disconnected
or damaged.
Motor is blocked.
Motor is jammed and Motor is blocked.
makes a noise
Cutting height is too low.
Loud noises, the mower Screws on motor, its fixing or
is rattling on the mower chasing are
loose.
Mower runs unevenly or Blade is damaged / worn or the
vibrates strongly
blade mounting is released.
Blade is very dirty.
(4) .
Part no. 529370590
Part no. 529370790
Part no. 529370890
Remedy
v Connect the mains cable or
if necessary replace it.
v Remove the obstacle.
v Remove the obstacle.
v Raise the cutting height.
v Let the screws be tightened
by an authorised specialist
dealer.
v Replace the blade.
v Clean the mower
(see 4. MAINTENANCE).
If this does not rectify the
problem, replace the blade.
07.10.20 13:54