Advertisement
Imported by Furniture Solutions (Aust) Pty Ltd
10-16 Daisy St,
Revesby, NSW. 2212
www.furnituresolutions.com.au
Imported by Furniture Solutions (Aust) Pty Ltd New South Wales, Australia.
For any assistance with assembly or for missing parts please contact:
Place of purchase or Furniture Solutions on below
Customer Service (Australia) Phone-1300 794 188
Email- customerservice@furnituresolutions.com.au
INSTRUCTION MANUAL
CAESAR EXT TOP DINING TABLE
ITEM CODE: 17CAET68SG
1
17CAET68SG
Advertisement
Table of Contents
Related Manuals for Furniture Solutions CAESAR EXT 17CAET68SG
Summary of Contents for Furniture Solutions CAESAR EXT 17CAET68SG
- Page 1 10-16 Daisy St, Revesby, NSW. 2212 www.furnituresolutions.com.au Imported by Furniture Solutions (Aust) Pty Ltd New South Wales, Australia. For any assistance with assembly or for missing parts please contact: Place of purchase or Furniture Solutions on below Customer Service (Australia) Phone-1300 794 188 Email- customerservice@furnituresolutions.com.au...
-
Page 2: Pre-Assembly Preparation
PRE-ASSEMBLY PREPARATION Before you start: Choose a clean, level, spacious assembly area. Avoid hard surfaces that may damage the product Take care when lifting. Product should be assembled as near as possible to the point of use Ensure that you have all required contents for complete assembly Always read the assembly instructions carefully before beginning assembly. -
Page 3: Parts List
PARTS LIST PART CODE 1 TABLE TOP PVA9961-VDT 2 TABLE LEG PVA9961-VDL 3 X TABLE LEG PVA9961-VDXL 17CAET68SG... - Page 4 FIT TABLE LEGS Prepare product as per page 2: Position table top upside down on a soft level surface IE: Floor with clean carpet or thick blanket on harder surface. Note 2 people will be required thru most of the assembly. When table top [1] is in position take note of the thread holes in base, you will note a grouping of 3 threaded holes in a triangle pattern and a single threaded hole to right of the triangle of holes.
- Page 5 FIT TABLE LEGS Step 2: To fit other table legs [2] ensure you have leg facing away from centre of table top as indicated in drawing below. Aline all three holes in table leg with three threaded holes in table top.
- Page 6 STEP 3: STAND TABLE ON LEGS Please note this is a very heavy item and will require 2 reasonably strong people to pick up and place into position. One person at each end looking down the length of the table. Please get a good grip and lift table using your knees straight up into air, now carefully in mid air rotate table over until feet can touch the floor.
- Page 7 OPERATING INSTRUCTIONS FOR EXT ON TABLE Auto Riser Action operation. Please locate under table top 2 black plastic toggles [as shown in diagram step 1] one on each side of table near extension piece. These are part of the locking function if in locked position you can not operate extension function.
-
Page 8: Care And Maintenance
CARE AND MAINTENANCE About ceramic material: Ceramics are generally made by taking mixtures of clay, earthen elements, powders, and water and shaping them into desired forms. Once the ceramic has been shaped, it is fired in a high temperature oven known as a kiln. In general, they are hard, corrosion-resistant and have a higher scratch resistance than glass. -
Page 9: Safety Warnings And Advice
SAFETY WARNINGS AND ADVICE Notices and Advice Please be advised that materials used in your furniture are not impervious to neglect, acts of god, abuse, alcohol spills, improper use of chemicals such as bleach or any solvent based products Please be advised that heat sources such as direct sunlight, log fires, heaters and air conditioners can have adverse affects on your furniture. - Page 10 To make a warranty claim, customers can either contact the retailer where the purchase was made or Furniture Solutions on contact details below. Proof of purchase will be required before proceeding with any claim. In the case of product defects providing photos may be able to speed up processing of the claim.
Need help?
Do you have a question about the CAESAR EXT 17CAET68SG and is the answer not in the manual?
Questions and answers