Vigitron MaxiiPower Vi22301 Installation Manual

Vi22301 60W 12/24VDC PoE Splitter Installation Manual
The Vi22301 is a PoE splitter that is fully compliant with IEEE 802.3af
(15.4W), IEEE 802.3at (30W) and 60W standards. When used with a PoE
switch or PoE Midspan, it accept 30W or 60W PoE input and data, then
generate 30W PoE and data output and regulates the PoE high voltage to
12VDC or 24VDC.
It is designed to power PoE IP devices and Non-PoE IP devices and can
provide 12VDC or 24VDC up to 30W. The output voltage is selected by a
slide switch. The Vi22301 is equipped with over current protection to
safeguard connected devices and can operate at extended temperature of
-40°C to +75°C. It is compact in size and can fit easily in most camera
housings. The Vi22301 can be combined with extenders to provide remote
DC power over UTP, Coax or single pair wire at distances up to 3,000
without the need for local power supplies.
The Vi22301 is capable of meeting the demanding power requirements for
access control, lighting, emergency phone systems and cameras with
heaters/blowers. It is an ideal solution for providing remote power to PoE IP
devices and non-PoE IP devices and save installation time and cost.
Important Safety Warning
- Read these instructions.
- Keep these instructions.
- Follow all instructions.
- Heed all warnings.
- Do not use this apparatus near water.
- Clean only with a dry cloth.
- Install in accordance with the manufacturer's instructions.
- This installation should be made by a qualified service person and should
conform to all local codes.
- DO NOT bundle UTP or Coax signals in the same conduit as high-voltage
wiring.
- To reduce the risk of fire or electrical shock, do not expose these products
to rain, moisture, dripping or splashing.
- No objects filled with liquids, such as vases, shall be placed on Vigitron
equipment.
- DO NOT install the unit in a place where the operating ambient tempera
ture exceeds 75° C.
- Make sure that the external power supply output voltage is in the recom
mended range.
- Do not install near any heat sources such as radiators, heat registers,
stoves or other apparatus (including DVRs) that produce heat.
- Protect the power cord from being walked on or pinched particularly at
plugs, convenience receptacles, and the point where they exit from the
apparatus.
- Only use attachments/accessories specified by the manufacturer.
- Unplug this apparatus during lightning storms or when unused for long
periods of time.
- Refer all servicing to qualified service personnel. Servicing is required
when the apparatus has been damaged in any way, such as a power
supply cord or plug is damaged, liquid has been spilled, or objects have
fallen into the apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped.
- The mains plug is used as the disconnect device and shall remain readily
operable.
RISK OF ELECTRIC SHOCK
CAUTION: TO REDUCE THE RISK OF ELECTRICAL SHOCK,
DO NOT REMOVE COVER. NO USER SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
CAUTION
DO NOT OPEN
The Smart Choice for Transmission Solutions
WARNING! - To reduce the risk of fire or electric shock, do not expose
this apparatus to rain or moisture. This apparatus should not be exposed to
dripping or splashing and no objects filled with liquids, such as vases should
be placed on the apparatus.
WARNING! - This apparatus is a Class I product. This product must
be connected to a mains socket outlet thru a PoE source device.
WARNING! - The main plug is used as the disconnect device and
should remain readily operable.
Application Drawing
Powering PoE and non-PoE devicesdistances
Non-PoE Switch
Vi10240
56VDC
Vi30210
Data
328 ft. (100m)
The Vi22301 can power a wide range of PoE devices while providing 12VDC or 24VDC to
non-PoE devices.
IP Camera-end Installation
- Select the output voltage using with the slide switch on the opposite side
of RJ45 connectors.
- Use the 12/24VDC output to power a non-PoE device. Be sure to observe
polarity where Red is Positive & Black is Negative.
- Connect a standard Cat5/6 cable of maximum 100m in length from a PoE
switch or Midspan to the Vi22301 DATA+PoE input port.
- Connect another Cat5/6 cable to the DATA+PoE output port of the
Vi22301 to a camera (PoE IP device) or non-PoE IP device.
Ethernet Switch/NVR-end Installation
- The other end of the RJ45 cable needs to be connected to a PoE capable
port of a PoE switch or a Midspan. The PoE port need to be able to provide
enought power to the Vi22301 and its connected PoE device.
Maxii Power
Vi22301
Data + PoE
12/24VDC
Data + 60W PoE
328 ft. (100m)
Vi22301
Data + PoE
Data + 60W PoE
328 ft. (100m)
12/24VDC
Vi22301
Data + PoE
Data + 60W PoE
328 ft. (100m)
12/24VDC
www.vigitron.com
TM
Cat 5/6
Emergency
Call Box
IP Camera
Emergency
Light
IP Camera
LED Light