Vigitron MaxiiFiber Vi50004 Installation Manual

Vi50004 4-Port Media Converter Installation Manual
Vigitron's Vi50004 is a 4-port fiber to UTP media converter enabling
Ethernet signals to be transmitted over different types of fiber optic cables.
The use of SFP fiber modules results in compatibility with all major single
and multimode fiber optics cables to achieve desired transmission
distances depending on the type of cables and SFPs. The Vi50004 is an
efficient solution for connecting uplinks from multiple network switches to
headend in IDF to MDF system configurations using fiber cables. The
Vi50004 expands fiber transmission capacity for most switches that have
just two fiber ports. With the growing number of cameras requiring 1G
connection, the Vi50004 provides an efficient solution for systems that
multiple of these cameras are used.
Up to four Vi50004 can be placed in a Vi5000R to create rackmountable
headend solutions from 4 to 16 ports providing cost effective solutions for
any size applications.
Important Safety Warning
- Read and keep these instructions.
- Heed all warnings.
- Follow all instructions.
- Do not use this apparatus near water.
- Clean only with a dry cloth.
- Install in accordance with the manufacturer's instructions.
- This installation should be made by a qualified service person and should
conform to all local codes.
- To reduce the risk of fire or electrical shock, do not expose these products
to rain, moisture, dripping or splashing.
- No objects filled with liquids, such as vases, shall be placed on Vigitron
equipment.
- DO NOT install the unit in a place where the operating ambient tempera
ture exceeds 70° C.
- Make sure that the external power supply output voltage is in the
recommended range.
- Do not install near any heat sources such as radiators, heat registers,
stoves or other apparatus that produce heat.
- Protect the power cord from being walked on or pinched particularly at
plugs and the point where they exit from the apparatus.
- Only use attachments/accessories specified by the manufacturer.
- Unplug this apparatus during lightning storms or when unused for long
periods of time.
- Refer all servicing to qualified service personnel. Servicing is required
when the apparatus has been damaged in any way, such as a power
supply cord or plug is damaged, liquid has been spilled, or objects have
fallen into the apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped.
- The power plug is used as the disconnect device and shall remain readily
operable.
RISK OF ELECTRIC SHOCK
CAUTION: TO REDUCE THE RISK OF ELECTRICAL SHOCK,
DO NOT REMOVE COVER. NO USER SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
CAUTION
DO NOT OPEN
The Smart Choice for Transmission Solutions
WARNING! - To reduce the risk of fire or electric shock, do not expose
this apparatus to rain or moisture. This apparatus shall not be exposed to
dripping or splashing and no objects filled with liquids, such as vases shall
be placed on the apparatus.
WARNING! - This apparatus is a Class I product. This product must
be connected to a mains socket outlet thru an AC to DC Power supply.
WARNING! - The mains plug is used as the disconnect device and
shall remain readily operable.
Application Drawing
Network Switch
Vi50004
Power
Supply
Data
Long Distance Fiber
Data
Long Distance Fiber
Data
Long Distance Fiber
Data
Long Distance Fiber
The Vi50004 along with Vi50000 enables addging fiber connection to any network switch. SFPs
need to be added to Vi50004 and Vi50000A to match the fiber optic cables.
IP Camera-end Installation
- Insert a suitable 1000MBps SFP into the SFP socket of the Vi50000A. The
SFP needs to match the specification of the fiber optics cable.
- Connect the fiber connector of the optical wire to the SFP.
- If the IP Camera is non-PoE use an approved 12VDC or 48VDC power
adapter to power the Vi50000A.
- If the IP Camera is PoE enabled use the Vi0017 or another approved
48VDC power adapter to power the Vi50000A.
- Connect the IP camera RJ45 connector to the "10/100BaseT Ethernet" port
of Vi50000A using a standard Cat5/6 cable of maximum 100m in length.
The link LED on the 10/100 connector should be "ON" to indicate proper
connection between the camera and Vi50004.
Ethernet Switch/NVR-end Installation
- Connect an approved 12VDC power supply to the power connector of
Vi50004. An Octopus power cable is provided to simplify connection. Each
port can also use PoE if provided from switch.
- Connect the RJ45 connector of the Ethernet switch to the 100/1000BaseT
Ethernet port of Vi50004 using a standard Cat5/6 cable of maximum
328 feet (100 m) in length.
- Insert a suitable 1000Mbps SFP into the SFP socket of the Vi50004. The
SFP needs to match the specification of the fiber optics cable.
- Connect one end of the long fiber optic cable to a SFP module.
The Ethernet link, Fiber link, activity LEDs should be "ON" and "Blink" to
indicate the status of each port.
Note: As no standards exist between SFP and network switches the switch port bandwidth
setting may have to be fixed at 1000Mbps (1G).
Media Converter
Vi50000A
PoE Camera
Data + 60W PoE
328 ft. (100m)
Power
Supply
Vi50000A
Data + 60W PoE
328 ft. (100m)
Power
Supply
Vi50000A
PoE Camera
Data + PoE
328 ft. (100m)
Power
Supply
Vi50000A
PoE Camera
Data + PoE
328 ft. (100m)
Power
Supply
www.vigitron.com
UMVi50004-0521