Contents Introduction Declaration of conformity Symbols Introduction In the event of items missing or visible damage EC Declaration of conformity This manual contains information and please contact us on 01245 324560. prescriptions marked by the following symbols. Declaration of conformity We, Smith’s Environmental Products Limited 1-2 Blackall Industrial Estate Symbols used in this guide...
Important safety and installation instructions Prior to installation, read these installation and operating instructions. The installation and operation should also be in accordance with national regulations and accepted codes of good practice. 8. Electrical connection This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if Important: Connection to the power supply must be effected by means of a fixed they have been given supervision or instruction concerning use of the appliance in a safe...
Product dimensions Product performance Heat output Heat Output at 80° Heat Output at 75° Heat Output at 70° Model Normal Boost Normal Boost Normal Boost return (kW) (kW) (kW) (kW) (kW) (kW) (kW) (kW) (kW) flow ECOVECTOR II SMART LL 640 ECOVECTOR II SMART LL 1030 ECOVECTOR II SMART LL 1390 100mm min.
Installation - product 4. Commissioning 5. Installation completion Check for water leaks. Remove any trapped air from the system via the vent valve on the top left 1. Turn on the electrical supply at the fused spur. Refit outer casing to the chassis and secure hand side of the heat exchanger.
Quick user guide for Wi-Fi LCD Icon descriptions Button functions Thermostat Function Increase Button Decrease Button Fan Speed Low, Medium, High, Auto, Off Long press Short press (2sec) Heat/Cool/Eco Digital Offset, Time Mode selection Button Permanent override Programmable Program- AUTO schedule mable Heat/Cool/Eco...
Getting started 1. When powered for the first time the control 5. Select the thermostat in this case set to which is heating only. will boot (Software version will appear) after a sort time the display will change to show All units are factory configured in off-line stand “U9 - Yes”...
Page 8
Changing from offline Factory reset User Guide Scan for equipment Press from the App and mode to online mode follow the on screen instructions. If you have made an error or need to change For further information and to view detail of set your system parameters, or want to return to up, operation and parameters, please consult the If you want to use the internet App and the...
Ecovector II Smart LL ® Fault finding Providing the power supply is switched on and the thermostat control is calling for heat the heater will with Smart Controls switch on and off automatically with the central heating system. In the event of any difficulty, please contact us on +44 (0) 1245 324560. It will be helpful if you do not disconnect the heater from the central heating system.
How it works How to operate LCD Icon descriptions Getting started Your Ecovector ll Smart is designed to Ensure your central heating is ON, the controls All units are factory configured in off-line stand operate as part of your central heating system calling for heat (Setpoint above the room alone mode and tested for function when built.
Adding controls to User Guide network (UG600) For further information and to view detail of set up, operation and parameters, please consult the 1. When powered for the first time the control full manual at: will boot (Software version will appear) after a https://salus-controls.com/uk/product/fc600/#downloads sort time the display will change to show “U9 - Yes”.
Fault finding Accessories Disposal Providing the power supply is switched on and the thermostat control is calling for heat the heater will As part of the policy of continuous product Universal Gateway Hub UG600 for use with switch on and off automatically with the central heating system. internet App control improvement, Smith’s Environmental Products LTD reserves the right to alter specification without...
Page 13
Happy to help To view the full product information download the datasheet at: Smith’s Environmental Products Ltd is one of the leading manufacturers of heating and cooling www.SmithsEP.co.uk products in the UK. We are committed to achieving the highest standards and our faith is For product information, customer services or supported by a free parts and labour guarantee sales support call us on +44 (0) 1245 324900...