1. Manuals
  2. Brands
  3. Valence Tech Manuals
  4. Control Unit
  5. iBT-07
  6. Manual

Valence Tech iBT-07 Manual

Bluetooth module for audio application
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
This module is limited to OEM installation ONLY
Bluetooth Module for Audio Application
(
Doc. Name :
Date
:
Revision
:
Copyright ©, 2012 by Engineering Department, Valence Semiconductor Design Limited.
All rights reserved. No part of this document may be reproduced, transmitted, transcribed,
stored in a retrieval system, or translated into any language, in any form or by any means
without the prior written permission of Valence Semiconductor Design Limited.
0.6.01
iBT-07
Qualified QDID : B020169 )
iBT-07-Rev0.6.01
2012-11-29
0.6.01
Bluetooth Module for Audio Application
1 / 12
iBT-07
2012-11-29

Advertisement

Table of Contents
loading

Related Manuals for Valence Tech iBT-07

Summary of Contents for Valence Tech iBT-07

  • Page 1 Bluetooth Module for Audio Application iBT-07 This module is limited to OEM installation ONLY Bluetooth Module for Audio Application Qualified QDID : B020169 ) Doc. Name : iBT-07-Rev0.6.01 Date 2012-11-29 Revision 0.6.01 Copyright ©, 2012 by Engineering Department, Valence Semiconductor Design Limited.

  • Page 2: Pin Drawing

    Bluetooth Module for Audio Application 1. Overview iBT-07 is a Class 2 Bluetooth module supporting Bluetooth v3.0 specification. It is implemented by using the CSR8610 ROM chip. iBT-07 is designed for receiving audio data transmitting from a mobile device. It can also be used to control the audio playing function of the remote device.

  • Page 3: Pin Description

    Bluetooth Module for Audio Application 5. Pin Description Application Pin Name Pin Descriptions Usage Type Ground MIC_AP Microphone A Positive Input MIC_AN Microphone A Negative Input SPK_LN Negative Output of Left Speaker SPK_LP Positive Output of Left Speaker No Connect...
  • Page 4 I, WPD wake up the iBT-07 module O4 4mA output pad Strong Pull-up OD Open drain output pad Strong Pull-down Input Weak Pull-up Schmidt Trigger Input Weak Pull-down Bidirectional Analog Table 1 iBT-07 Pin Description Table 0.6.01 4 / 12 2012-11-29...

  • Page 5: Electrical Specification

    Bluetooth Module for Audio Application 6. Electrical Specification 6.1. Absolute Maximum Rating Item Symbol Rating Unit Power Supply Voltage -0.4 to 3.7 Peak Current 0 - 70 °C Storage Temperature -20 to 85 6.2. Recommended Operating Condition Item Symbol...
  • Page 6 Bluetooth Module for Audio Application 6.4. RF Characteristics VDD=3.3V, operating temperature = 20 °C unless specified otherwise Bluetooth Receiver Units Miin Spec ≦ -70 Sensitivity at 0.1% BER ≧-20 Maximum Receiver Signal at 0.1% BER ≦ 11 C/I Co-Channel ≦...
  • Page 7 Bluetooth Module for Audio Application 7. Module Dimension and PCB Layout Guideline 7.1. Module Dimension 7.2. PCB Layout Guideline 15mm 15mm ANTENNA CLEARANCE AREA 0.9mm 0.6mm 1.6mm 0.6.01 7 / 12 2012-11-29...

  • Page 8: Fcc Statement

    Exposure information. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This device should be installed and operated with a minimum distance of 20cm between the antenna and all persons. Label requirements: Contains Transmitter Module FCC ID: ORP-IBT-07 Host use instruction: The module must install and work with a speaker, The speaker’s manufacturer is ValenceTech Limited.

  • Page 9: Mobile Device

    This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. A label must be affixed to the outside of the end product into which the iBT-07 Module is incorporated, with a statement similar to the following: For iBT-07:...
  • Page 10 OEM LABELING REQUIREMENTS FOR END-PRODUCT The iBT-07 module is labeled with its own FCC ID Certification Number. The FCC ID certification numbers are not visible when the module is installed inside another device, as such the end device into which the module is installed must display a label referring to the enclosed module.
  • Page 11 FCC ID of the module is visible; then an additional permanent label referring to the enclosed module: “Contains Transmitter Module FCC ID: ORP-IBT-07” or “Contains FCC ID: ORP-IBT-07” must be used. The host OEM user manual must also contain clear instructions on how end users can find and/or access the module and the FCC ID.
  • Page 12 Bluetooth Module for Audio Application Valence Semiconductor Design Ltd. Unit 1, 20/F., APEC Plaza, 49 Hoi Yuen Road, Kwun Tong, Hong Kong Tel: (852) 2797 3288 Fax: (852) 2776 7770 http://www.valencetech.com The information in this publication is believed to be accurate in all respects at the time of publication but is subject to change without notice. Valence Semiconductor Design Ltd.

Table of Contents