Table of Contents
Advertisement
Quick Links
Bluetooth Module for Audio Application
(
Doc. Name :
Date
:
Revision
:
This module is limited to OEM Installation only.
Copyright ©, 2012 by Engineering Department, Valence Semiconductor Design Limited.
All rights reserved. No part of this document may be reproduced, transmitted, transcribed,
stored in a retrieval system, or translated into any language, in any form or by any means
without the prior written permission of Valence Semiconductor Design Limited.
0.3.01
iBT-03
Qualified QDID : B019566 )
iBT-03-Rev0.3.01
2012-07-30
0.3.01
Bluetooth Module for Audio Application
1 / 7
iBT-03
2012-07-30
Advertisement
Table of Contents
Related Manuals for Valence Tech iBT-03
Summary of Contents for Valence Tech iBT-03
- Page 1 Bluetooth Module for Audio Application iBT-03 Bluetooth Module for Audio Application Qualified QDID : B019566 ) Doc. Name : iBT-03-Rev0.3.01 Date 2012-07-30 Revision 0.3.01 This module is limited to OEM Installation only. Copyright ©, 2012 by Engineering Department, Valence Semiconductor Design Limited.
-
Page 2: Pin Drawing
Bluetooth V2.1 + EDR specification. It is implemented by using the CSR BlueCore5-Multimedia ROM chip. iBT-03 is designed for receiving audio data transmitting from a mobile device. It can also be used to control the audio playing function of the remote device 2. -
Page 3: Pin Description
Active High Input for ON / OFF control PIO13 STBY / ON When iBT-03 is OFF, a high pulse in this pin will turn it ON. When iBT-03 is in ON, a high pulse in this pin will turn in OFF 3.3V 3.3V 3.3V Supply Input... -
Page 4: Electrical Specification
VDD=3.3V, operating temperature = 25 °C unless specified otherwise Item Symbol Miin Unit Standby Mode Pairing Mode 10.0 iBT-03 is discoverable by other devices Idle Mode iBT-03 is connectable with devices in the 10.0 connected list Audio Streaming Mode 80.0 0.3.01 4 / 7 2012-07-30... - Page 5 Bluetooth Module for Audio Application 6.5. RF Characteristics VDD=3.3V, operating temperature = 20 °C unless specified otherwise Bluetooth Receiver Units Miin Spec ≦ -70 Sensitivity at 0.1% BER ≧-20 Maximum Receiver Signal at 0.1% BER ≦ 11 C/I Co-Channel ≦...
- Page 6 Bluetooth Module for Audio Application 7. Module Dimension and PCB Layout Guideline 7.1. Module Dimension 2.54mm 1.46mm x 14 = 20.44mm 2.97mm 0.95mm iBT-03 Module (Top View) 0.8mm R=0.38mm 23.24mm 5.33mm 1.66mm 2.54mm 7.2. PCB Layout Guideline 0.3.01 6 / 7...
-
Page 7: Fcc Statement
Exposure information. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This device should be installed and operated with a minimum distance of 20cm between the antenna and all persons. Label requirements: Contains Transmitter Module FCC ID: ORP-IBT-03 Host use instruction: The module must install and work with a speaker, the speaker's manufacturer is ValenceTech Limited. - Page 8 FCC RF radiation exposure limits set forth for an uncontrolled environment. 3. A label must be affixed to the outside of the end product into which the iBT-03 module is incorporated, with a statement similar to the following: For iBT-03: This device contains FCC ID: ORP-IBT-03.
- Page 9 demonstrated to regulations for other transmitter components within the host product; to requirements for unintentional radiators (Part 15B). To ensure compliance with all non-transmitter functions the host manufacturer is responsible for ensuring compliance with the module(s) installed and fully operational. If a host was previously authorized as an unintentional radiator under the Declaration of Conformity procedure without a transmitter certified module and a module is added, the host manufacturer is responsible for ensuring that the after the module is installed and operational the host continues to be compliant with the Part 15B unintentional radiator...
- Page 10 FCC and Industry Canada authorization. OEM LABELING REQUIREMENTS FOR END-PRODUCT The iBT-03 module is labeled with its own FCC ID Certification Number. The FCC ID certification numbers are not visible when the module is installed inside another device, as such the end device into which the module is installed must display a label referring to the enclosed module.
- Page 11 FCC and Industry Canada multi-transmitter product procedures. The end product with an embedded FCC ID:ORP-IBT-03 Module may also need to pass the FCC Part 15 unintentional emission testing requirements and be properly authorized per FCC Part 15.
- Page 12 Bluetooth Module for Audio Application Valence Semiconductor Design Ltd. Unit 1, 20/F., APEC Plaza, 49 Hoi Yuen Road, Kwun Tong, Hong Kong Tel: (852) 2797 3288 Fax: (852) 2776 7770 http://www.valencetech.com The information in this publication is believed to be accurate in all respects at the time of publication but is subject to change without notice. Valence Semiconductor Design Ltd.