Table of Contents
Advertisement
Timer Recording
Up to 8 timer recording programs can be made using G-
timer programing or Express timer programing method as far as a
year in advance. Remember, the clock must be set before you can
program the timer.
NOTES:
● If all the 8 programs have already been set, "PROGRAM FULL"
appears on the TV screen.
● After timer recording is completed, the recorder turns off
automatically.
● You can program the timer recording while a regular recording
is in progress; the menu screens will not be recorded.
● In case of a power failure after programming, the recorder's
memory backup keeps your selections (if the lithium battery is
not exhausted).
● If the tape reaches its end during recording, the recording stops
and "
" and " $" on the front display panel blink. Press 1
then
on the recorder to eject the cassette or press
0
on the remote control to rewind the tape.
®
G-
System Setup
CODE
INFORMATION
The G-
timer programming system eliminates the need to
CODE
input channel, date, start and stop time data when setting the
timer record function. Simply key in the G-
TV programme you wish to record (found in most TV listings) and
the recorder's timer is automatically programmed.
You have to set "GUIDE PROG" numbers, which are assigned to
each station for purposes of G-
the stations stored in your recorder's memory to get proper results.
Before G-
setup you must have performed the procedures of
CODE
Tuner Set and Clock Set.
IMPORTANT
Perform the following procedure after Auto Set Up and/or the
channel setting steps.
After setting the Guide Program Numbers, channel positions may
be incorrect if you stored or skipped channels. In this case, re-
perform Guide Program Number setting.
The SHOWVIEW system is not applicable with this model.
Guide Program Number Set
A
Access Main Menu screen, then Initial Set screen
Press MENU on the remote control. Press
pointer next to "INITIAL SET", then press OK or
B
Access G-
Setup screen
CODE
Press
to place the pointer next to "G-CODE/SHOWVIEW
rt
SETUP", then press OK or
e
C
Input Guide Prog number
Press
or the Number keys to select
rt
the Guide Program number as shown in
the TV listing, then press OK or
D
Input receiving channel number
Press
or the Number keys to select
rt
the number of the channel on which the
Guide Program number's broadcasts are
received, then press OK or
e
● If the satellite broadcast is received on
your recorder's auxiliary channel ("L-1"
or "F-1"), select "L-1" or "F-1" for the channel position to which
the satellite receiver is connected.
● Repeat steps 3 and 4 as necessary.
E
Return to normal screen
Press MENU on the remote control.
CODE
number for the
CODE
timer programming, for all
CODE
to place the
rt
.
e
.
G-CODE/SHOWVIEW SETUP
GUIDE PROG
2
.
e
[0–9] OR [ / ] : SELECT
[MENU] : EXIT
G-CODE/SHOWVIEW SETUP
GUIDE PROG
2
.
[0–9] OR [ / ] : SELECT
[MENU] : EXIT
G-
CODE
The G-
CODE
next to the program in most TV listing.
● Remember, the clock must be set
before you can program the timer.
● Be sure to read "G-
Setup".
● Load a cassette with the record safety
tab intact. The recorder turns on, and
the counter is reset, automatically.
● Select the appropriate colour system
with "PAL/MESECAM" and "NTSC"
in Function settings.
A
Press PROG on the remote control
to access the G-
G-CODE/SHOWVIEW NO.
3
[0 – 9]
[+/–] : EXPRESS PROGRAMING
[PROG] : EXIT
B
Press the appropriate Number keys to input the G-
number, then press OK. Check to make sure the setting is
accurate on the G-
G-CODE/SHOWVIEW NO.
1 2 3 4 5 6 7 8
[0 – 9]
[ ] : DELETE
[PROG] : EXIT
● If the G-
screen appears after pressing OK,
press the Number keys, PR+/– or
to input the number of the
rt
channel on which the broadcast for
the G-
the recorder, then press OK.
● To set the tape speed, press SP/LP/EP (
● To change the stop time, press STOP+/–.
● To timer-record daily (Monday–Friday) or weekly serials,
press DAILY (number key 8) or WEEKLY (number key 9).
Pressing the button again makes the "DAILY" or "WEEKLY"
display disappear.
● If you made a mistake, press & to access the G-
again.
● If an incorrect G-
already finished has been input, "ERROR" is displayed for
about 5 seconds, then the G-
C
Press OK or PROG.
● If "PROGRAM OVERLAPPED" appears, see "Program
overlap warning display" (
D
Press
. The recorder turns off automatically and "
#
displayed on the display panel.
TV PROG
5
TV PROG
5
— 8 —
®
Timer Programing
numbers are the numbers
®
System
CODE
screen.
CODE
Program screen.
CODE
NO. 12345678
START
21:00
DATE
25.04
: [OK]
/S
V
Setup
CODE
HOW
IEW
number is received on
CODE
number or the one for a broadcast
CODE
CODE
9).
CODE
– P1 –
STOP
22:00
SP
TV PROG
1
G-CODE/SHOWVIEW SETUP
GUIDE PROG
TV PROG
2
5
[0–9] OR [ / ] : SELECT
[PROG] : EXIT
).
p
screen
CODE
screen reappears.
" is
#
Advertisement
Table of Contents
