Maintenance - Craftsman CMCST930 Instruction Manual

6. Wind the cutting line onto the spool in the direction of
the arrow on the spool. Make sure to wind the line on
neatly and in layers. Do not crisscross.
7. When the wound cutting line reaches the recesses
cut the line.
8. Fit the spool onto the appliance as described in
Replacing Spool Assembly.

MAINTENANCE


WARNING:
of serious personal injury, turn unit off and
remove the battery pack before making any
adjustments or removing/installing attachments
or accessories, when replacing line, or prior to
cleaning. An accidental start‑up can cause injury.
Your CRAFTSMAN power tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
Cleaning

WARNING:
all air vents with clean, dry air at least once a week.
To minimize the risk of eye injury, always wear ANSI
Z87.1 approved eye protection when performing
this procedure.

WARNING:
harsh chemicals for cleaning the non‑metallic parts
of the tool. These chemicals may weaken the plastic
materials used in these parts. Use a cloth dampened
only with water and mild soap. Never let any liquid get
inside the tool; never immerse any part of the tool into
a liquid.
Accessories

WARNING:
those offered by CRAFTSMAN, have not been tested with
this product, use of such accessories with this product
could be hazardous. To reduce the risk of injury, only
CRAFTSMAN recommended accessories should be used
with this product.
Recommended accessories for use with your product are
available at extra cost from your local dealer or authorized
service center. If you need assistance in locating any
accessory, please contact CRAFTSMAN call 1‑888‑331‑4569.
29
To reduce the risk
Blow dirt and dust out of
Never use solvents or other
Since accessories, other than
Replacing the Guard with an
Extended Coverage Guard (Fig. F, G)
An extended coverage guard is available (sold separately) for
,
extra coverage if desired.
Use replacement Part number nA248689.

WARNING:
APPLIANCE WITHOUT GUARD FIRMLY IN PLACE.
The guard must always be properly attached on the
appliance to protect the user.
Removing the Current Guard
1. Remove the guard screw
2. Slide the guard
Assembling the New Guard
1. Slide the guard into place as shown in Fig. F, G.
2. Slide the guard
Make sure the tabs
on the trimmer head.
3. Continue to slide the guard on until it "snaps"into place.
The locking tab
4. Using a crosshead screwdriver, insert the guard screw
and tighten securely.
Versatrack™ (Fig. R)

WARNING:
personal injury, turn unit off and remove the
battery pack before making any adjustments or
removing/installing attachments or accessories.
An accidental start‑up can cause injury.

WARNING:
personal injury, do not use a damaged Versatrack™
hang hook or Versatrack™ Trackwall. A damaged
Versatrack™ hang hook or Versatrack™ Trackwall will
not support the weight of the tool.

WARNING:
personal injury, DO NOT suspend tool overhead or
suspend objects from the hang hook. ONLY suspend
tool on the Versatrack™ Trackwall using the hang hook.

WARNING:
does not exceed the maximum rated weight of 20 lb
(9 kg) for the selected Versatrack™ hook.

WARNING:
Versatrack™ Trackwall rail, adequately space the tools
in order to not exceed 75 lb (35 kg) per linear foot.
iMPORTAnT: Versatrack™ accessories mount compatible
tools securely to the Versatrack™ Trackwall system.
NEVER OPERATE
19 shown in Fig. F, G.
11 off.
11 fully onto the motor housing
20 on the guard engage the ribs
18 should snap into the housing slot
To reduce the risk of serious
To reduce the risk of serious
To reduce the risk of serious
Ensure that the tool weight
When hanging objects on a
English
7 .
16
17 .
19
13