Operation; Installing And Removing The Battery Pack - Craftsman CMCST930 Instruction Manual

Attaching the Auxiliary Handle (Fig. H)
1. Remove handle knob
auxiliary handle 6 .
2. Push the auxiliary handle
trimmer pole 8 as shown in Fig. H.
3. Thread the handle bolt
on the auxiliary handle
4. Thread the handle knob
and firmly tighten. Ensure the handle is secured in
position before using.
5. To adjust the position of the auxiliary handle, loosen the
handle knob 18 and slide the auxiliary handle
down the pole until it is in the desired location. Tighten
the handle knob 18
in position.
Releasing the Cutting Line (Fig. A)
In transit, the cutting line is taped to the spool housing
• Remove the tape holding the cutting line to the spool housing.

OPERATION


WARNING:
personal injury, turn unit off and remove the
battery pack before making any adjustments or
removing/installing attachments or accessories,
when replacing line, or prior to cleaning. An
accidental start‑up can cause injury.

Installing and Removing the Battery Pack

(Fig. I)

WARNING:
the off position before inserting the battery pack.
nOTE: For best results, make sure your battery pack is
fully charged.
1. To install the battery pack
the battery pack with the rails inside the tool's handle
and slide it into the handle until the battery pack is firmly
seated in the tool and ensure that it does not disengage.
2. To remove the battery pack from the tool, press the
release button 13 and firmly pull the battery pack out of
the tool handle. Insert it into the charger as described in
the charger section of this manual.
Proper Hand Position (Fig. K)

WARNING:
personal injury, ALWAYS use proper hand position
as shown.

WARNING:
personal injury, ALWAYS hold securely in anticipation
of a sudden reaction.
Proper hand position requires one hand on the main
handle 5 and one hand on the auxiliary handle
18 and handle bolt 19
6 onto the top of the upper
19 through the mounting hole
6 .
18 onto the handle bolt
to secure the auxiliary handle
To reduce the risk of serious
Ensure the tool/appliance is in
12 into the tool handle, align
To reduce the risk of serious
To reduce the risk of serious
6
Switching Trimmer On and Off (Fig. A)
from the

WARNING:
trigger in the on position.
1. To turn the appliance on, press the lock‑off button
then squeeze the trigger
may release the lock‑off button.
19
2. To turn the appliance off, release the trigger.
Speed Control Switch (Fig. J)
This string trimmer gives you the choice to operate at a
more efficient speed to extend the runtime for larger jobs, or
6 up or
accelerate the trimmer speed for high‑performance cutting.
6 To accelerate the trimmer, push the speed control
switch 3 forward toward the auxillary handle
position. This mode is best to cut through heavier growth
and for applications that need higher RPM.
10 .
To extend runtime, pull the speed control switch back
toward the battery housing
mode is best for larger projects that require more time
to complete.
nOTE: When in "HI" mode, runtime will be decreased as
compared to when trimmer is in "LO" mode.
Line Feed Button (Fig. J)
The line feed feature allows you to advance the length of
cutting line available while trimming.
• To extend the cutting line, fully depress the line feed
button
nOTE: The trimmer will stop cutting when the line feed
button is pressed and will resume cutting when released.
nOTE: For maximum line length, press the button multiple
times until you hear the cutting line hitting the guard. Do not
continue to press the line feed button once the maximum
length is reached. This will result in overfeeding and will
consume string quickly.
Trimming (Fig. K—M)

WARNING:
roughly parallel with the ground (tilted no more
than 10 degrees). This trimmer is not an edger. DO
NOT TILT the trimmer so that the string is spinning
near a right angle to the ground. Flying debris can
cause serious injury.

CAUTION:
pets are at least 100' (30 m) away. Flying debris can
cause serious injury.
1. With the trimmer on, angle it and swing side to side as
shown in Fig. L.
2. Maintain a cutting angle of 5 ° to 10 °. Do not exceed
10 °. Cut with the tip of the line.
3. Maintain a minimum distance of 24" (610 mm) between
the guard and your feet as shown in Fig. M.
.
Never attempt to lock the
1 . Once the unit is running, you
21 into the "LO" position. This
4 while trimming and then release.
Keep the rotating string
Ensure that other persons and
English
2 and
6 into the "HI"
11