VT-16P250WS / VT-24P370WS: 16 / 24 Port L2 Web Smart Ethernet PoE Switch Introduction Power-over-Ethernet (PoE) eliminates the need to run DC power to other devices on a wired LAN. Using a Power- over-Ethernet system, installers need to run only a single Category 5 Ethernet cable that carries both power and data to each device.
VT-16P250WS / VT-24P370WS: 16 / 24 Port L2 Web Smart Ethernet PoE Switch Link/Act LED: Green (for megabit ports): Indicates that the port is running at 100M. Green (for gigabit ports): Indicates that the port is running at 1000M. Blinking: Indicates that the switch is either sending or receiving data to the port.
VT-16P250WS / VT-24P370WS: 16 / 24 Port L2 Web Smart Ethernet PoE Switch The switch can be mounted in an EIA standard size 19-inch rack; which can be placed in a wiring closet with other equipment. To install, attach the mounting brackets to the switch’s side panels (one on each side) and secure them with the screws provided.
VT-16P250WS / VT-24P370WS: 16 / 24 Port L2 Web Smart Ethernet PoE Switch The following steps let you connect the switch to a protective ground: Step 1: Verify if the system power is off. Step 2: Use the ground cable to place the #8 terminal lug ring on top of the ground-screw opening, as seen in the figure below.
Page 7
VT-16P250WS / VT-24P370WS: 16 / 24 Port L2 Web Smart Ethernet PoE Switch Data receive positive TPRXD+ Input Data receive negative TPRXD- Input UTP port explanation for Gigabit Ethernet is shown as follows: Pin NO. Description Name Note Data transmission positive...
VT-16P250WS / VT-24P370WS: 16 / 24 Port L2 Web Smart Ethernet PoE Switch Troubleshooting This section is intended to help solve the most common issues with the PoE Switch Incorrect connections Every port on this switch can automatically detect either straight or crossover cables when you link it with other Ethernet devices but other devices may demand a specific cable type (depending on the device).
VT-16P250WS / VT-24P370WS: 16 / 24 Port L2 Web Smart Ethernet PoE Switch 5.1 Management Options The Switch can be managed through any port on the device by using the Web-based Management Each switch must be assigned its own IP Address, which is used for communication with Web-Based Management.
VT-16P250WS / VT-24P370WS: 16 / 24 Port L2 Web Smart Ethernet PoE Switch 6.2 Administrator Administrator -> Authentication Configuration Here you can enter a new Username/Password and confirm it. The factory default IP address: 192.168.2.1 Username: admin Password: system Administrator -> System IP Configuration There are two ways for the switch to obtain an IP address: Static and DHCP (Dynamic Host Configuration Protocol).
Page 11
VT-16P250WS / VT-24P370WS: 16 / 24 Port L2 Web Smart Ethernet PoE Switch with IP address is 192.168.2.1 and subnet mask is 255.255.255.0 Administrator -> System Status Comment: By entering a Comment, the device can more easily be recognized on the LAN.
Page 12
VT-16P250WS / VT-24P370WS: 16 / 24 Port L2 Web Smart Ethernet PoE Switch Administrator -> Firmware Update You must enter the password of device in order to determine the firmware needs to be updated. After a correct password the switch will erase the old firmware first.
VT-16P250WS / VT-24P370WS: 16 / 24 Port L2 Web Smart Ethernet PoE Switch 6.3 Port Management Port Management -> Port Configuration In this page, the status of all ports can be monitored and adjusted for optimum configuration. Enable: Enable or disable the port’s connection...
Page 14
VT-16P250WS / VT-24P370WS: 16 / 24 Port L2 Web Smart Ethernet PoE Switch Addr. Learning: Enable or disable port learning MAC address. Port Management -> Port Mirroring Port Mirroring is a method of monitoring network traffic that forwards a copy of each incoming and/or outgoing packet from one port of the Switch to another port where the packet can be studied.
VT-16P250WS / VT-24P370WS: 16 / 24 Port L2 Web Smart Ethernet PoE Switch TX Rate: This allows you to enter data receive rate from 0 to 255 (base on speed base), 0 for full speed. RX Rate: This allows you to enter data transmit rate from 0 to 255 (base on speed base), 0 for full speed.
Page 16
VT-16P250WS / VT-24P370WS: 16 / 24 Port L2 Web Smart Ethernet PoE Switch Port Based VLAN: Port-Based VLANs are the simplest and most common form of VLAN. It assigns the appliance LAN ports to VLANs, effectively transforming the appliances. You can assign multiple ports to the same VLAN, or each port to a separate VLAN.
VT-16P250WS / VT-24P370WS: 16 / 24 Port L2 Web Smart Ethernet PoE Switch 6.5 Per Port Counter Per Port Counter -> Port Counter The Statistics screen displays the status of each port packet count. 6.6 QoS Setting QoS Setting -> Priority Mode...
VT-16P250WS / VT-24P370WS: 16 / 24 Port L2 Web Smart Ethernet PoE Switch 6.9 Trunking Trunking -> Link Aggregation Settings The Trunking function allows the switch to combine two or four ports together to increase bandwidth. Select the Trunking Groups, choose the Members to be grouped together, and then click Submit to activate the...
VT-16P250WS / VT-24P370WS: 16 / 24 Port L2 Web Smart Ethernet PoE Switch you can restore configuration settings from the file. Backup or restore the configuration file to or from your local drive. Click Download to save the current settings to your disk.
VT-16P250WS / VT-24P370WS: 16 / 24 Port L2 Web Smart Ethernet PoE Switch 6.13 SNMP Settings 6.14 Logout Click this to end this session Note: If you close the web browser without clicking the Logout button, it will be seen as an abnormal exit and the...
VT-16P250WS / VT-24P370WS: 16 / 24 Port L2 Web Smart Ethernet PoE Switch 6.15 PoE PoE -> PoE Setting This section provides PoE (Power over Ethernet) Configuration and PoE output status of PoE Switch. Main Power consumption: The Statistics screen displays the total Watts usage of PoE Switch.
Page 26
VT-16P250WS / VT-24P370WS: 16 / 24 Port L2 Web Smart Ethernet PoE Switch PoE -> PoE Scheduling PoE Schedule user can configure a duration time for PoE port as default value does not provide power. Note: Please enable NTP and correct the System Time first.
Page 27
VT-16P250WS / VT-24P370WS: 16 / 24 Port L2 Web Smart Ethernet PoE Switch System Time: Display current time information NTP Server: Assign #1 or #2 NTP server IP address manually Time Zone: Select the time zone according to current location PoE ->...
Page 28
VT-16P250WS / VT-24P370WS: 16 / 24 Port L2 Web Smart Ethernet PoE Switch Set Port No.: Select the port witch you want to set IP Address IP Address: Allow assign IP address witch you want to monitor Checking Time: Select time interval of ping action (1-10Min) Reset Delay Time: Select time PD Reset time (1-3Seconds) Enable Checking Port.
Page 29
VT-16P250WS / VT-24P370WS: 16 / 24 Port L2 Web Smart Ethernet PoE Switch Detailed Specifications - VT-16P250WS Ports 16 - 10/100Base-TX PoE Ports / 2 Combo ports (10/100/1000Base-T or 1000Base-X). PoE ports 16 - 10/100Base-TX ports PoE Standard IEEE802.3af, IEEE802.3at, per port 30W(MAX)
Page 30
VITEK warrants to the purchaser that products manufac- tured by VITEK are free of any rightful claim of infringement or the like, and when used in the manner intended, will be free of defects in materials and workmanship for a period of three (3) years, or as otherwise stated above, from the date of purchase by the end user.