Related Manuals for Meridian HARVEST H10 Series
Summary of Contents for Meridian HARVEST H10 Series
- Page 1 H1062 & H1072 Read this manual before using product. Failure to follow instructions and safety precautions can result in serious injury, death, or property damage. Keep manual for future reference.
- Page 2 H10XX Series Augers: Important Notes At 15-20 miles, tire lug nut tightness and wheel hub temperature need to be checked. At 50-60 miles, check these a second time. For all models, the maximum transport speed is mph.
- Page 3 Harvest by Meridian thanks you for your purchase of the best quality auger on the market. We are proud to have you on our team. Our equipment is manufactured in the United States of America and is made to improve your farming operation.
-
Page 4: Table Of Contents
TABLE OF CONTENTS 1. Introduction_____________________________________________________________4 2. Safety First______________________________________________________________5 3. Transportation & Placement_____________________________________________6 3.1 Before Transporting Your Auger___________________________________6 3.2 Transport Procedure_______________________________________________7 3.3 Placement of Auger________________________________________________7 3.4 Final Placement___________________________________________________9 3.5 Lowering the Auger_______________________________________________9 4. Operation______________________________________________________________10 4.1 Pre-Operation Checklist__________________________________________10 4.2 Auger Drive & Lockout___________________________________________10 4.3 Start Up &... -
Page 5: Introduction
Keep this manual handy for frequent reference and to pass on to new operators or owners. Call your Harvest by Meridian distributor or dealer if you need assistance, information, or additional copies of the manual. -
Page 6: Safety First
2. Safety First Safety is a priority in your everyday work habit, especially if you work with machinery. Whether you are an owner, an operator, or an employee, it is your responsibility to know the operational requirements and safety precautions of the machinery. -
Page 7: Transportation & Placement
Failure to do this could cause damage to the auger, and serious injury or death. All Harvest by Meridian augers have minimum clearance positions when in transport mode. Place auger in full down position. -
Page 8: Transport Procedure
3.2 Transportation Procedure Move auger with a tractor only. Never attempt to move by hand. Under no condition should you allow riders on the auger or tractor. Transport the auger no faster than 15 mph. When roads are rough or surfaces are uneven, slow down to ensure safe travel. - Page 9 WARNING: Never position raisers of any kind under the wheels of the auger to increase height. This includes pieces of wood, cement blocks, bricks, etc. Attempting this could result in damage to the equipment and personal injury or death. Make sure that the hitch is secured to the tractor, and that all hydraulic connections are tight and in good working condition.
-
Page 10: Final Placement
3.4 Final Placement of Auger When you are ready to use your auger, place the auger in its lowered position, and slowly back it up to your bin or storage facility, keeping an eye out for any people or obstructions in the hazard zone. DANGER: Avoid any electrical wires and overhead obstructions. -
Page 11: Operation
4. Operation Wear protective gear at all times when operating auger, such as hard hats, protective shoes, eye protection, and gloves. Do not wear loose clothing, and be sure that hair is tied back. 4.1 Pre-Operation Checklist Before operating the auger, the operator must follow this checklist: All safety shields are in place, secure, and in good working order. -
Page 12: Start Up & Break In
not exceed the maximum operation length of 34 inches of PTO driveline, or the maximum angularity of 30 degrees. Lockout/Shutdown of PTO Driveline: Turn off engine. Remove ignition key from tractor. If for some reason, you cannot remove the key, remove the PTO driveline from the tractor. -
Page 13: Everyday Operation
4.4 Everyday Operation WARNING: When auger is in operation, keep your hands, clothing, and other objects away from intake hopper, drive chains, and all other parts of auger to avoid personal injury. For normal auger operations, the following procedure and safety precautions are strongly recommended: Complete the pre-operation checklist before using your auger. -
Page 14: Completion & Cleanup
If auger is full of grain, do not restart at full speed. Engage PTO at low RPM and gradually increase power until normal operating speed is achieved. CAUTION: Starting the auger under load may result in damage to the auger. Make sure there is no blockage. -
Page 15: Hydraulics
Escaping hydraulic fluid can be nearly invisible under high pressure. Use some type of backdrop when searching for leaks. Harvest by Meridian augers have a velocity fuse for hydraulic safety. If the hydraulic line breaks, it locks the system. Our shut off valve is equipped with a flow restrictive orifice. -
Page 16: Cylinder Hydraulics
Relieve all pressure and then disconnect. 5.2 Cylinder Hydraulics The testing done on Harvest by Meridian auger hydraulics was done using a pressure gauge with 3000psi maximum rating. This was used simply as a guide. The psi requirements for an individual auger may vary slightly. -
Page 17: Storage & Maintenance
Always replace damaged or worn parts before using the auger. Use only replacement parts manufactured by Harvest by Meridian Use of unauthorized parts will void the warranty of your auger. Contact your Harvest by Meridian dealer to order parts. Harvest by Meridian augers are designed and tested for a safe, e cient operation. -
Page 18: Storage Of Auger
Lube Recommendation: Lube cross and bearing every 8 hours of use. Lube telescoping members yearly. NOTICE: Replacement parts are not lubricated. When you receive these parts in, make sure to lubricate and tighten screws. Mechanical Chain Drive: Keep drive chain tension adjusted to about ¼” deflection by loosening the four bolts on the lower bearing, then retightening. -
Page 24: H1062 & 72 Parts Book
AUGER MODEL(S) PART/ASSEMBLY NO. PART/ASSEMBLY DESCRIPTION TUBE, FRAME ASSY H1062 10314 (X2) (41 FT CABLE) 3RD TUBE ASSY. (SEE DRAWING #PBH10003) 10313 (X2) (29 FT CABLE) 2ND TUBE ASSY. (SEE DRAWING #PBH10002) CARRIAGE ASSY. (SEE DRAWING #PBH10009) 1ST TUBE ASSY. (SEE DRAWING #PBH10001) INFEED HOUSING ASSY (SEE DRAWING #PBH10010) - Page 25 AUGER MODEL(S) PART/ASSEMBLY DESCRIPTION PART/ASSEMBLY NO. TUBE, FRAME ASSY H1072 4TH TUBE ASSY. (SEE DRAWING #PBH10005) 10314 (X2) (41FT CABLE) 3RD TUBE ASSY. (SEE DRAWING #PBH10004) 10313 (X2) 2ND TUBE ASSY. (29FT CABLE) (SEE DRAWING #PBH10002) CARRIAGE ASSY. (SEE DRAWING #PBH10009) 1ST TUBE ASSY.
- Page 26 M O DEL(S) P ART/ ASSEMBLY DES C RIPTI O N H1062, H1072, H1082 C ARRIA G E ASM, H10XX SEE N O TE DETAIL B DETAIL A DETAIL C N O TES: 1) USE P/ N 30072 F O R H1062 & H1072 DRA WIN G N O .
- Page 27 P ART/ ASSEMBLY DES C RIPTI O N M O DEL(S) H1062, H1072, H1082 C ARRIA G E ASM, H10XX DETAIL D P/ N 30082 N O T SH O W N F O R C LARITY DETAIL E DRA WIN G N O . PBH10009...
- Page 28 P ART/ ASSEMBLY DES C RIPTI O N M O DEL(S) H1062, H1072, H1082 C ARRIA G E ASM, H10XX DES C RIPTI O N ITEM N O . P ART N O . Q TY SH A FT, MID HIN G E, 1" X 17" L O N G 10149 PLATE, C R O SS M O UNT C ARRIA G E STA BILIZER 10197...
- Page 29 AUGER MODEL(S) PART/ASSEMBLY NO. PART/ASSEMBLY DESCRIPTION DRAWING NO.
- Page 30 AUGER MODEL(S) PART/ASSEMBLY DESCRIPTION PART/ASSEMBLY NO. DRAWING NO.
- Page 31 AUGER MODEL(S) PART/ASSEMBLY DESCRIPTION PART/ASSEMBLY NO. DRAWING NO.
- Page 33 M O DEL(S) P ART/ ASSEMBLY DES C RIPTI O N H1062, H1072, & H1082 TUBE ASSEMBLY, 1ST TUBE DETAIL A DETAIL B DRA WIN G N O . PBH10001...
- Page 34 P ART/ ASSEMBLY DES C RIPTI O N M O DEL(S) H1062, H1072, & H1082 TUBE ASSEMBLY, 1ST TUBE DETAIL C DES C RIPTI O N ITEM N O . P ART N O . Q TY 1 / 2" C LA MP, G ALV , VINYL,HYDRA ULI C H O SE RETAIN 10151 BENT PIN, 1 / 2"X7", SWIN G H O PPER LIFT RETAIN 10191...
- Page 35 P ART/ ASSEMBLY DES C RIPTI O N M O DEL(S) H1062, H1072 TUBE ASSEMBLY, 2N D TUBE DETAIL C DETAIL B DETAIL A DES C RIPTI O N ITEM N O . P ART N O . Q TY 1 / 2"...
- Page 36 P ART/ ASSEMBLY DES C RIPTI O N M O DEL(S) H1062 TUBE ASSEMBLY, 3RD, H1062 DETAIL A DETAIL B DETAIL C DRA WIN G N O . PBH10003...
- Page 37 P ART/ ASSEMBLY DES C RIPTI O N M O DEL(S) H1062 TUBE ASSEMBLY, 3RD, H1062 DES C RIPTI O N ITEM N O . P ART N O . Q TY TRUSS, UPRI G HT 10163 BRA C KET, C A BLE TRUSS M O UNT, UPPER 10171 TRUSS, C R O SS MEMBER T O P 10174...
- Page 38 AUGER MODEL(S) PART/ASSEMBLY DESCRIPTION PART/ASSEMBLY NO. 3RD TUBE ASSEMBLY H1072 Detail B Detail C Detail A DRAWING NO. PBH10004...
- Page 39 AUGER MODEL(S) PART/ASSEMBLY NO. PART/ASSEMBLY DESCRIPTION 3RD TUBE ASSEMBLY H1072 10171 BRACKET, CABLE TRUSS MOUNT, UPPER NUT HEX FLG_~375-16 UNC_SIMP NUT, 3/8-16UNC, HEX, FLANGE, GRD 5, ZINC NUT HEX FLG_~500-13 UNC_SIMP NUT, 1/2-13UNC HEX, FLANGE, GRD 5, ZINC 10163 TRUSS, UPRIGHT HEX HD FLG_~500-13 UNC_1~5_SIMP BOLT, 1/2-13UNC X 1-1/2"...
- Page 40 AUGER MODEL(S) PART/ASSEMBLY NO. HOPPER ASSEMBLY H1062, H1072, H1082, A1072 Detail C NOTE: A10XX SERIES AUGERS USE SWING HOPPER WELDMENT #30722, REMAINING PARTS ARE AS SHOWN Detail B NOT SHOWN: DRAWING NO. 10319-CHAIN,#50 X 58 ROLLERS + CONNECTOR LINK PBH10012...
- Page 42 P ART/ ASSEMBLY DES C RIPTI O N A U G ER M O DEL(S) H1062,H1072,H1082 TUBE ASSY,SWIN G H O PPER,10" DETAIL A N O TE: ITEM # 6 USED O NLY O N M O DELS WITH O UT G E ARB O X G USSET DETAIL B DRA WIN G N O .
- Page 43 A U G ER M O DEL(S) P ART/ ASSEMBLY DES C RIPTI O N H1062,H1072,H1082 TUBE ASSY,SWIN G H O PPER,10" DES C RIPTI O N ITEM N O . P ART N O . Q TY KEY, 1 / 4 X 1-1 / 2", S Q U ARE 10309 LYN C H PIN, 1 / 4"...
- Page 44 P ART/ ASSEMBLY DES C RIPTI O N A U G ER M O DEL(S) A 10XX & H10XX PT O SH A FT ASM, C O MPLETE, 10" DETAIL A N O TES: 1) C O MP O NENTS O F P/ N 30087-08 ARE N O T A V AILA BLE. 30087-08 IS S O LD AS IS. DES C RIPTI O N ITEM N O .
- Page 49 P ART/ ASSEMBLY DES C RIPTI O N A U G ER M O DEL(S) A 10XX, H10XX, H13XX WIN C H & M O UNT BRA C KET ASSEMBLY DES C RIPTI O N ITEM N O . P ART N O . Q TY BENT PIN, 1 / 2"X7", SWIN G H O PPER LIFT RETAIN 10191...
-
Page 50: Warranty Policy & Forms
TOLL FREE: 1-800-667-5904 WEB: www.harvestauger.com...
Need help?
Do you have a question about the HARVEST H10 Series and is the answer not in the manual?
Questions and answers