Table of Contents
Advertisement
Indoor UNIT No. before setup change is displayed.
5
1. Specify CODE No. [14] with Move the cursor to
select "Code(DN)" with the "
<"
[
F1] button, then set "Code(DN)" with the
[
˄ ] / [
˅ ] button.
(CODE No. [14]: Group address)
2. Change the SET DATA from [0001] to [0002] with
Move the cursor to select "Data" with the
"
>" [
F2] button, then set "Data"
with the [
˄ ] / [
˅ ] button.
(SET DATA [Header unit: 0001] [Follower unit:
0002])
3. Push the [
MENU] button to set the other
Code (DN) and Data. After "Continue?" is
displayed on the screen, push the
"
Yes" [
F1] button.
Indoor UNIT No. before setup change is displayed.
6
If there is other indoor unit to be changed,
2
5
repeat procedure
to
to change the
setup.
When the above setup has finished, push
Select the group-controlled function on the
menu screen, then push the "
[
F2] button.
47-EN
Push the "
unit" [
F1] button to
select the unit to set.
The selected unit changes as follows each
time the button is pushed:
Push the "
Set" [
F2] button.
The setting display for the selected unit
appears.
before change of setup, specify CODE No. [12],
[13], [14] in order with Move the cursor to
select "Code(DN)" with the "
[
F1] button, then set "Code(DN)" with the
[
˄ ] / [
˅ ] button. and then check the
changed contents.
Address change check Before change:
[3-3-1] → After change: [2-2-2]
The contents of which
setup was changed.
2
(In this case, procedure from
is repeated.)
Indoor UNIT No. before setup change is displayed.
Set"
7
After check of the changed contents, Push
the "
No" [
finish the setting operation. "
appears on the screen for a while, then the
screen returns to the "Field setting menu"
screen.
Pushing the "
displays the unit selection screen when the
group control is used. Push the [
button on the unit selection screen to finish
the setting operation. "
the screen for a while, then the screen returns
<"
to the "Field setting menu" screen.
– 24 –
46 °F (8 °C) operation
F2] button to
Setting"
Pre-heating operation can be set for cold regions
where room temperature drops to below zero.
1
Push the [
MENU] button to display the
menu screen.
No" [
F2] button
Push and hold the [
CANCEL]
the [
˅ ] button at the same time to
display the "Field setting menu".
Setting" appears on
Push and hold the buttons for more than 4
seconds.
Push the [
˄ ] / [
"DN setting" on the "Field setting menu"
screen, then push the "
[
F2] button.
The fan and louver of the indoor unit operate.
When the group control is used, the fan and
louver of the selected indoor unit operate.
Specify CODE No. [D1]
Move the cursor to select "Code(DN)" with the
"
< " [
"Code(DN)" with the [
Move the cursor to select "Data" with the
"
>" [
with the [
˄ ] / [
SET DATA
46 °F (8 °C) Operation setting
0000
0001
46 °F (8 °C) Operation setting
Push the [
CANCEL] button to return.
MENU] button and
˅ ] button to select
Set"
F1] button, then set
˄ ] / [
˅ ]button.
F2] button, then set "Data"
˅] button.
None
(Factory default)
EN
48-EN
Advertisement
Table of Contents
