Program Chart - Diplomat ADP8352 User Manual

Program Chart

To select the most suitable program for the dishes to be washed refer to the table
below, which indicates the most appropriate program according to dish type and
degree of soiling.
Cycle Cycle
Selection
Information
Very dirty dishes,
pots and pans. (Not
to be used with deli-cate
items)
Heavy Duty
Normal dirty dishes,
pots and pans. Standard
daily cycle.
Normal Wash
Normal dirty dishes,
pots and pans without
dried on residue.
Light Wash
(IEC-EN50242)
Economic, fast cycle to
be used for items which
are sensitive to higher
temperatures.Run imm-
ediately after dishes are
Glassware used.
Economic, fast cycle to
be used to on not very
dirty dishes right after
they are used. No drying
Rapid Wash cycle.
Pre-wash of dishes
pots and pans while
waiting for the load to
be completed after the
Rinse subsequent meal.
Description of Detergent
Cycle
Pre-wash with hot water.
Extended wash at 70 C.
Rinse with cold water. 30g
Rinse with hot water at 70 C.
Drying.
The second pre-wash uses cold
water.
Extended wash at 50 C.
Rinse with cold water. 30g
Rinse with hot water at 70 C.
Drying.
Pre-wash with cold water.
Extended wash at 50 C.
Rinse with cold water. 30g
Rinse with hot water at 70 C.
Drying.
Wash at 50 C.
Rinse with warm water.
Hot rinse at 70 C. 15g
Drying.
Short wash at 40 C.
Cold rinse. 15g
Short cold wash to prevent
food residue from drying on none
the dishes .
Starting the Wash Program
6
1
Rinse-
aid
Yes
Turn on the water to the appliance, partially open the door of the dishwasher, and
press the ON-OFF button "3" located on the control panel. The power indicator light '4'
will come on. At this point, the appliance is on and ready to be programmed.
Setting and Starting a wash Cycle
Choose the desired programme by pressing the programme selection button '5'. Each
time it is pressed, the programme indicator lights '1' will come on in succession.
Yes
Choose the wash programme most appropriate for the type of dishes to be washed,
and the amount of soil; following the wash cycle table contained in this manual.
Close the door and after a few seconds the programme will start automatically
and cannot be modified. If necessary, read the paragraph entitled,
"Cancelling or modifying a cycle while underway."
Yes
Cancelling or modifying a cycle while underway...
A cycle that is underway can only be modified if it has only been running for a short
time, otherwise, the detergent may have already been used, and the appliance may
have already drained the wash water. If this is the case, the detergent dispenser must
Yes
be refilled (see the paragraph entitled, "Loading the Detergent").
To change the cycle currently underway, open the door carefully (in order to avoid
being sprayed by hot water). Press and hold the programme select button '5' for about
5 seconds. Once the cycle has been cancelled, the dishwasher will emit a short beep
and the relative indicator light will turn off. To set a new wash cycle, follow the
instructions contained in the paragraph entitled, "Setting and Starting a Wash Cycle."
No
If you forget to load some of the dishes...
The wash cycle can be interrupted by opening the door carefully (in order to avoid
being sprayed by hot water). When the door is closed again, the cycle will
automatically restart at the point where it left off.
No
At the end of the wash cycle...
The end of the cycle will be indicated by six beeps and the indicator light '1' remain
turned on. After the six beeps, the indicator light '1' will turn off. Open the door, turn
off the appliance using the ON/OFF switch '3' and turn off the water supply to the unit.
Wait a few minutes before removing the dishes to avoid handling them while still hot
and to get a better drying result.
2
6 7
5
11
4
3
6h 4h 2h
ADP 8352
8
9