Bosch GWS 20-180 H Professional Instructions Manual page 19

Angle grinder
Rated speed
Max. grinding disc diameter
Grinding spindle thread
Max. thread length of grinding spindle
Weight according to EPTA-Procedure 01:2014
– with additional low-vibration auxiliary
handle
– with standard auxiliary handle
Protection class
The specifications apply to a rated voltage [U] of 230 V. These specifications may vary at different voltages and in country-specific models.
When switching on power tools with starting current limitation, the voltage drops briefly. Interference with other equipment may occur in the
event of unfavourable conditions in the electricity supply. Malfunctions are not expected if the impedances in the electricity supply are below
0.25 ohms.
Noise/Vibration Information
Noise emission values determined according to EN 60745-2-3.
Typically the A-weighted noise level of the power tool is: Sound pressure level 92 dB(A); sound power level 103 dB(A). Uncer-
tainty K = 3 dB.
Wear hearing protection
Total vibration values a (triax vector sum) and uncertainty K determined according to EN 60745-2-3:
h
Grinding surfaces (roughing):
a
h
K
Grinding with abrasive disc:
a
h
K
The vibration level given in these instructions has been
measured in accordance with a standardised measuring pro-
cedure and may be used to compare power tools. It can also
be used for a preliminary estimation of exposure to vibra-
tion.
The stated vibration level applies to the main applications of
the power tool. However, if the power tool is used for differ-
ent applications, with different application tools or poorly
maintained, the vibration level may differ. This can signific-
antly increase the exposure to vibration over the total work-
ing period.
To estimate the exposure to vibration accurately, the times
when the tool is switched off or when it is running but not ac-
tually being used should also be taken into account. This can
significantly reduce the exposure to vibration over the total
working period.
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
power tool and application tools, keeping the hands warm,
and organising workflows correctly.
Bosch Power Tools
GWS 20-180 H GWS 20-230 H
-1
min 8500
mm 180
M 14
mm 25
kg 5.1
kg 5.0
/ II
2
m/s
2
m/s
2
m/s
2
m/s
Fitting
Fitting Protective Equipment
Pull the plug out of the socket before carrying out any
u
work on the power tool.
Note: If the grinding disc breaks during operation or the
holding fixtures on the protective guard/power tool become
damaged, the power tool must be sent to the after-sales ser-
vice immediately; see the "After-sales service and advice on
using products" section for addresses.
Protective guard for grinding
Place the protective guard (5) on the spindle collar. Adjust
the position of the protective guard (5) to the requirements
of the operation and lock the protective guard (5) with the
locking screw (6).
Adjust the protective guard (5) such that sparking in
u
the direction of the operator is prevented.
English | 19
GWS 21-180 H GWS 21-230 H
6600 8500
230 180
M 14 M 14
25 25
5.4 5.1
5.3 5.0
/ II / II
GWS 20-180 H GWS 21-180 H
GWS 20-230 H GWS 21-230 H
3 601 H49 L.. 3 601 H51 L..
3 601 H50 L.. 3 601 H52 L..
9.5
1.5
5.5
1.5
1 609 92A 431 | (21.11.2018)
6600
230
M 14
25
5.4
5.3
/ II
9.5
1.5
4.0
1.5