Advertisement
Quick Links
INSTALLATION GUIDE
SOL FUSION PLUS® SHOWER MIXER
SYSTEM REQUIREMENTS
Unequal Pressure - Venturi jet installed
Operating Pressures - refer to the Venturi Selection Table on page 2
Equal High (Mains) & Equal Low Pressures - Venturi jet removed
Operating Pressures
Operating Hot Water Temperatures
Operating Cold Water Temperatures
Do not plug outlet when testing.
This shower mixer can be line tested up to 1500kPa (217.6psi)
AS/NZS 3500.1 states that pressures above 500kPa can cause damage from water hammer, reduce the life of
appliances, taps & fittings, cause excessive noise in the system and recommend that a pressure limiting valve (PLV) be fitted.
WHAT IS IN THE PACK
Faceplate + O-Ring
Handle
IMPORTANT:
Factory fitted WITHOUT
Venturi Jet
BEFORE INSTALLATION
Pipework MUST be purged before connecting to the mixer
MIXER ORIENTATION
This mixer is designed to be connected with the hot water
supply on the left only and the cold water supply on the
right only.
If at any point the cartridge nut is removed, please ensure
that both black lines marked on the cartridge and cartridge
nut are aligned when the mixer is in full cold position as
shown in figure 1.
Patented New Zealand No. 605175
Mixer Assembly
MINIMUM
Hot
20kPa (2.9psi)
300kPa (43.5psi)
36kPa (5.1psi)
55° C
5° C
3x Venturi Jets for Unequal Pressures:
20-35kPa
GREEN
JET
YELLOW
Grub Screw
Handle Cap
OUTLET
HOT
INLET
ONLY
MAXIMUM
Cold
1500kPa (217.6psi)
1500kPa (217.6psi)
60° C
N/A
36-75kPa
76-130kPa
JET
RED
JET
8g x 32 Dome Head
Square Drive
Stainless Steel Screws
2.5mm Allen Key
COLD
INLET
ONLY
( FULL COLD POSITION )
Figure 1.
Page 1
Advertisement
Summary of Contents for Adesso SOL FUSION PLUS
- Page 1 INSTALLATION GUIDE SOL FUSION PLUS® SHOWER MIXER SYSTEM REQUIREMENTS MINIMUM MAXIMUM Cold Unequal Pressure - Venturi jet installed 1500kPa (217.6psi) Operating Pressures - refer to the Venturi Selection Table on page 2 20kPa (2.9psi) 300kPa (43.5psi) Equal High (Mains) & Equal Low Pressures - Venturi jet removed 36kPa (5.1psi)
- Page 2 IF YOU HAVE... EQUAL LOW PRESSURE OR EQUAL HIGH/MAINS PRESSURE Install product as supplied. UNEQUAL PRESSURE 1. Check your hot & cold water pressure 2. Follow this flowchart to select the correct Venturi Jet for the pressure situation: 76-130kPa 36-75kPa YELLOW 20-35kPa GREEN...
-
Page 3: How To Install
HOW TO INSTALL Cut a hole to suit faceplate No minimum straight distance Ø90mm Faceplate Min 40mm Max 70mm Apply a silicone bead on the back of the faceplate Page 3 Patented New Zealand No. 605175... - Page 4 TROUBLESHOOTING - SWAPPING OUT THE VENTURI JETS Remove the insert disc using long nose pliers by carefully Remove the handle and disassemble the mixer: inserting the nose of the pliers into the indicated areas A & B. AREA A AREA B Unscrew the Venturi Jet using a 2.5mm Allen Key Refit the correct Venturi Jet into the insert disc and hand tighten firmly...
- Page 5 UPGRADING FROM UNEQUAL TO MAINS PRESSURE Remove the handle and disassemble the mixer: Remove the insert disc using long nosed pliers by carefully inserting the nose of the pliers into the indicated areas A & B. AREA A AREA B Refit the seal with silicone grease if required and then insert disc Unscrew the Venturi Jet using a 2.5mm Allen Key using the long nose pliers, ensuring that the locating pins go into the...