Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Ursalink UC1152
Summary of Contents for Ursalink UC1152
- Page 1 UC1152 Quick Start Guide...
-
Page 2: Related Documents
Thank you for choosing Ursalink UC1152 remote LoRa I/O. This guide describes how to install the UC1152 remote LoRa I/O and how to connect to Ursalink LoRaWAN gateway. Once you complete the installation, refer to the Ursalink UC1152 User Manual for instructions on how to perform configurations on the device. -
Page 3: Package Contents
Ursalink UC11 Quick Start Guide 1. Packing List Before you begin to install the UC1152 remote LoRa I/O, please check the package contents to verify that you have received the items below. 1.1 Package Contents Setscrews 1 × UC1152 1 × Stubby LoRa 1 ×... -
Page 4: Hardware Introduction
Ursalink UC11 Quick Start Guide 2. Hardware Introduction 2.1 Overview A. Front Panel LED Indicator Area System: System Indicator ACT: Network Indicator LoRa Antenna Connector Micro USB Interface Rear Panel 12-Pin Pluggable Terminal 2.2 Dimensions (mm) www.ursalink.com... -
Page 5: Led Indicators
Ursalink UC11 Quick Start Guide 2.3 Pinouts Definition IN_COM OUT_COM OUT_NC OUT_NO 2.4 LED Indicators Indication Status Description Solid On System booting System System Status On for 500ms, off for 500ms Working properly On for 100ms, off for 100ms Failed to send data... -
Page 6: Hardware Installation
The external LoRa antenna should be installed vertically always on a site with a good signal. 3.2 Connect the UC1152 to a Computer 3.4 Mount the UC1152 Use 2 pcs of flat head Phillips screws to fix the UC1152 onto the wall mounting. www.ursalink.com... -
Page 7: Getting Started
4. Connect to Ursalink LoRaWAN Gateway 4.1 Configure UC1152 via Toolbox UC1152, connect PC USB port to micro USB port of UC1152 remote LoRa I/O directly, PC Power on the Setup the Toolbox. Select Serial port and input the login password, default “123456”, then click “Save”... - Page 8 Ursalink UC11 Quick Start Guide www.ursalink.com...
- Page 9 Ursalink UC11 Quick Start Guide Click “LoRaWAN” configure the LoRaWAN parameters, Including the EUI, channels. ④ Click “Channel” configure RS485 modbus master channels ⑤ www.ursalink.com...
- Page 10 Ursalink UC11 Quick Start Guide 4.2 Configure LoRaWAN Gateway ① Log in the Gateway A. Start a Web browser on your PC (Chrome and IE are recommended), type in the IP address, and press Enter on your keyboard. B. Enter the username and password, click “Login”.
- Page 11 Ursalink UC11 Quick Start Guide Click “LoRaWAN → Packet Forwarder → Radios”, configure the frequency and channels of the ③ gateway Click “LoRaWAN → Network Server → General”, enable embedded Network Server ④ www.ursalink.com...
- Page 12 Ursalink UC11 Quick Start Guide Click “LoRaWAN → Network Server → Applications”, add applications ⑤ Click “LoRaWAN → Network Server → Profiles”, add profiles ⑥ www.ursalink.com...
- Page 13 Ursalink UC11 Quick Start Guide Click “LoRaWAN → Network Server → Device”, input the device EUI and application key of end node ⑦ Check device active status and packets ⑧ www.ursalink.com...
- Page 14 Ursalink UC11 Quick Start Guide Click “LoRaWAN → Network Server → Applications”, configure sending data from Network Server to ⑨ Application Server via HTTP or MQTT www.ursalink.com...
- Page 15 Ursalink UC11 Quick Start Guide [END] www.ursalink.com...