Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Texas Instruments FDC1004QEVM
Summary of Contents for Texas Instruments FDC1004QEVM
- Page 1 FDC1004QEVM User Guide User's Guide Literature Number: SNAU178 April 2015...
-
Page 2: Table Of Contents
..........................Setup ......................FDC1004QEVM ................... Input/Output Connector Description ......................... HW Setup ......................... SW Setup ........................Operation ........................Board Layout ........................... Schematic .......................... Revision History Table of Contents SNAU178 – April 2015 Submit Documentation Feedback Copyright © 2015, Texas Instruments Incorporated... - Page 3 FDC1004QEVM Schematic List of Tables ........................Ordering ........................ J1, J2 Pin Out ........................J4 Pin Out ........................J5 Pin Out ....................... Bill of Materials SNAU178 – April 2015 List of Figures Submit Documentation Feedback Copyright © 2015, Texas Instruments Incorporated...
-
Page 4: Introduction
FDC1004QEVM User's Guide Introduction The FDC1004QEVM evaluation kit is a plug and play system to test and evaluate the FDC1004Q, AEC- Q100 qualified, 4-channel capacitive to digital converter. The EVM is a breakable PCB which consists of 3 sections. The first section is a USB to I2C converter based on MSP430F5528 micro-controller, the second section contains the FDC1004Q and the third section is a touchless sensor (to demonstrate the sensitivity of the FDC1004Q) . -
Page 5: Input/Output Connector Description
USB to I2C FDC1004 SENSOR Figure 1. FDC1004QEVM : Sections Input/Output Connector Description J1, J2: 4x1 Header: the I/O ports of sections between the USB to I2C and the FDC1004Q sections. This provides the I2C communication channel and the power connections between these two sections should the EVM be separated into sections. -
Page 6: Hw Setup
I2C communication with FDC1004Q is fully managed by the MSP430F5528IRGC microcontroller (U3). The FDC1004Q has a fixed I2C address. SW Setup Ensure that the FDC1004QEVM GUI and the drivers have been installed on the host computer. Plug the EVM into an available USB port on the host. Operation Plug the EVM into the host computer. -
Page 7: Bottom Layer Routing
Board Layout www.ti.com Figure 3. Bottom Layer Routing SNAU178 – April 2015 FDC1004QEVM User's Guide Submit Documentation Feedback Copyright © 2015, Texas Instruments Incorporated... -
Page 8: Schematic
Schematic www.ti.com Schematic Figure 4. FDC1004QEVM Schematic FDC1004QEVM User's Guide SNAU178 – April 2015 Submit Documentation Feedback Copyright © 2015, Texas Instruments Incorporated... -
Page 9: Bill Of Materials
Mixed Signal MicroController, RGC0064B RGC0064B MSP430F5528IRGCT Micropower 150 mA Low-Noise Ultra Low-Dropout MF05A_N LP2985AIM5-3.3/NOPB Regulator, 5-pin SOT-23, Pb-Free CRYSTAL 24.000MHZ 18PF SMD ABMM ABMM-24.000MHZ-B2-T SNAU178 – April 2015 FDC1004QEVM User's Guide Submit Documentation Feedback Copyright © 2015, Texas Instruments Incorporated... -
Page 10: Revision History
Revision History NOTE: Page numbers for previous revisions may differ from page numbers in the current version. DATE REVISION NOTES April 2015 Initial release. Revision History SNAU178 – April 2015 Submit Documentation Feedback Copyright © 2015, Texas Instruments Incorporated... - Page 11 STANDARD TERMS AND CONDITIONS FOR EVALUATION MODULES Delivery: TI delivers TI evaluation boards, kits, or modules, including any accompanying demonstration software, components, or documentation (collectively, an “EVM” or “EVMs”) to the User (“User”) in accordance with the terms and conditions set forth herein. Acceptance of the EVM is expressly subject to the following terms and conditions.
- Page 12 FCC Interference Statement for Class B EVM devices NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
- Page 13 【無線電波を送信する製品の開発キットをお使いになる際の注意事項】 開発キットの中には技術基準適合証明を受けて いないものがあります。 技術適合証明を受けていないもののご使用に際しては、電波法遵守のため、以下のいずれかの 措置を取っていただく必要がありますのでご注意ください。 1. 電波法施行規則第6条第1項第1号に基づく平成18年3月28日総務省告示第173号で定められた電波暗室等の試験設備でご使用 いただく。 2. 実験局の免許を取得後ご使用いただく。 3. 技術基準適合証明を取得後ご使用いただく。 なお、本製品は、上記の「ご使用にあたっての注意」を譲渡先、移転先に通知しない限り、譲渡、移転できないものとします。 上記を遵守頂けない場合は、電波法の罰則が適用される可能性があることをご留意ください。 日本テキサス・イ ンスツルメンツ株式会社 東京都新宿区西新宿６丁目２４番１号 西新宿三井ビル 3.3.3 Notice for EVMs for Power Line Communication: Please see http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_02.page 電力線搬送波通信についての開発キットをお使いになる際の注意事項については、次のところをご覧くださ い。http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_02.page SPACER EVM Use Restrictions and Warnings: 4.1 EVMS ARE NOT FOR USE IN FUNCTIONAL SAFETY AND/OR SAFETY CRITICAL EVALUATIONS, INCLUDING BUT NOT LIMITED TO EVALUATIONS OF LIFE SUPPORT APPLICATIONS.
- Page 14 Notwithstanding the foregoing, any judgment may be enforced in any United States or foreign court, and TI may seek injunctive relief in any United States or foreign court. Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2015, Texas Instruments Incorporated...
- Page 15 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue.
- Page 16 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Texas Instruments FDC1004QEVM...
Need help?
Do you have a question about the FDC1004QEVM and is the answer not in the manual?
Questions and answers