1. 本製品について 1.1. 特徴 本製品は、Express5800/R120i-1M、あるいは、Express5800/R120i-2M ⽤の LOM カードです。 This product is that used on Express5800/R120i-1M or Express5800/R120i-2M. 本製品の取付に関する詳細は、本体装置のユーザーズガイドに記載しています。 本体装置に添付している「スタートアップガイド」を参照して、ユーザーズガイドを検索してください。 > See the latest User's Guide for the detailed function of this product. 1000BASE-T 接続 LOM カード(4ch)は 10/100BASE-T/TX、1000BASE-T に対応した RJ-45 ポートを 4 基有しています。この通信ポートを通してポートあたり最⼤...
Keep this Startup Guide at hand for quick reference at any time necessary. Be sure to read this section carefully. Precautions for Use -Be sure to read this section - The following includes information necessary for proper and safe operation of the product. Safety Indication Follow the instructions in this Startup Guide for your safety to use this product.
Term indicationg a degree of danger Description of a danger Symbol to draw attention Do not plug the power cord in a nonconforming outlet Use a wall outlet with specified voltage and power type. Otherwise, there is a risk of a fire or current leakage. Symbols Used in This Guide Attentions Indicates a risk of an electric shock.
NEC assumes no liability for any accident resulting in personal injury, death, or property damage if the product has been used in the above conditions.
Page 33
Connection Do not use any unauthorized interface cable. Use only interface cables authorized by NEC and locate a proper device and connector before connecting a cable. Using an authorized cable or connecting a cable to an improper destination may cause a short circuit, resulting in a fire.
Page 34
Precautions for Handling of Internal Devices Do not disassemble, repair, or modify the product yourself Do not disassemble, repair, or modify this product. Doing so may cause an electrical shock or a fire. Do not put the product close to fire, or immerse it in water. Doing so may cause an explosion.
Page 35
Anti-static Measures Installing or Uninstalling Internal Optional Devices (1) To avoid electric hazard and malfunction of the device, be sure to turn off the Power switch of the server and unplug the power cord from outlet before starting work, except for hot-swappable devices.
Dual Port 10/25GBASE SFP+ LOM Card has one or two optical transceiver module interfaces. And you can connect a SFP + module for 10GBASE-SR, SFP28 module for 25GBASE-SR. In addition, you can connect a DA (direct attached) cable. Do not install this product to a computer that is not recommended by NEC Corporation. Use supported optical modules(N8104-208).
Page 37
1.2. Description The functions of each part are as follows. LAN Port(N8104-206, N8104-207) A connector provides to access a network. For the types of connectable cables and how to connect, see “Network Cables”. SFP slot (LAN port)(N8104-208) A connector provides to access a network. For the types of connectable cables, see “7.2.Network Cables”(page E-19) .
Page 38
N8104-207 LINK PORT 1 PORT 2 Lamp Status Meaning On( Green) Link at 10Gbps speed On(Orange) Link at 100M/1Gbps speed LINK Link is down. Blink(Green) Traffic No traffic N8104-208 PORT 1 PORT 2 LINK Lamp Status Meaning On( Green) Link at 25Gbps speed LINK On( Orange) Link at 1G/10Gbps speed...
2. Hardware Installation/Uninstallation For hardware installation/uninstallation, refer to the User’s Guide of the server. - When the system is up, please turn the power off after shutdown process on the OS. and then unplug the AC power cord IMPORTANT: - For rack-type server, before open the top cover, need to disconnect the cable from this product.
3. Optical module Installation / Uninstallation The optical module may become hot. IMPORTANT: If you replace during operation, please remove the cable and change the temperature of the module before replacing it. For installing and uninstalling the optical module or cables, you do not need to turn OFF NOTE: the power of the server 3.1.
4. Driver/Firmware Setup The driver of this product is included “Starter Pack” of EXPRESS SERVER. “Starter Pack” is published on NEC web site. Starter Pack can be downloaded from NEC's support site. In addition, the driver may be temporarily released. Check the support information of this site and apply it as necessary.
5. Trouble Shooting 5.1. Unable to Start the System Check the adapter installation □ Make sure the adapter is connected to PCI-Express® slot firmly Check the adapter is connected firmly. If it is not so , Re-install the adapter Check the latch on the server for bracket fixing is not loose □...
Page 43
If the problem persists even after you checked the above items, something may be wrong with this adapter. Please contact to reseller, sales agents or service representative. EU Contact: NEC Nederland B.V. Olympia 4, 1213 NT Hilversum, The Netherlands E-15...
6. Notes in operation PXE boot on Legacy/UEFI is supported. PCI hot-plug, hot-add, hot-remove and hot-swap is not supported. AOC(Active Optical Cable) or DA cable(Active type) is not supported. Do not apply “F7 Default” in “Main Configuration Page” on “System Configuration” screen. The following functions are not supported in July 2021.
Cable Category 100BASETX : Cat.5 or better 1000BASE-T Cat.5e or better Length 100 m (max.) Limitation of N8104-206/207 less than12mm 11.58~11.79mm based on ISO standard. The width of the root portion of a plug should use the cable within 12mm.
Page 48
A “N8104-190 SFP28 module (25G-SR)” has an optical fiber interface based on IEEE802.3by 25Gigabit Ethernet® standard. The 25GbE SR standard enables 25GbE and full duplex transmissions at distances up to 100 meters using standard multi-mode fiber (MMF, 850nm wave length) cabling. Supported MMF cable listed below: Connector type: LC core/clad diameter...