HP Visualize c100 Install Manual
  1. Manuals
  2. Brands
  3. HP Manuals
  4. Desktop
  5. Visualize c100
  6. Install manual
HP Visualize c100 Install Manual

HP Visualize c100 Install Manual

Hp visualize c100: install guide
Hide thumbs Also See for Visualize c100:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Troubleshooting Manual, Installation Manual
Installing the C100 to C110 CPU Upgrade
HEWLETT
PACKARD
HP Part No. A4200-90011
E0895
Printed in USA

Advertisement

Table of Contents
loading

Related Manuals for HP Visualize c100

Summary of Contents for HP Visualize c100

  • Page 1 Installing the C100 to C110 CPU Upgrade HEWLETT PACKARD HP Part No. A4200-90011 E0895 Printed in USA...

  • Page 2: Preparing Your Workstation

    Preparing Your Workstation 1 Power off your workstation by pressing the power button on the front panel. When you press the power button, the workstation automatically shuts down the operating system before it powers off the system. 2 When the workstation has completed shutting down and powering off, power off the monitor, and any peripheral devices connected to the workstation.

  • Page 3: Removing The Main Tray Assembly

    Removing the Main Tray Assembly Removing the Main Tray Assembly 1 Completely loosen the four captive screws on the rear of the system unit, as shown in Figure 2. Captive Screws Figure 2 Removing Main Tray Assembly 2 Place one hand on the top of the system unit and push, while pulling the handle on the rear panel with your other hand.

  • Page 4: Removing The Cpu Board

    Removing the CPU Board Removing the CPU Board 1 Remove the CPU board retaining screw, as shown in Figure 3. Figure 3 Removing the CPU Board 2 Pull the two ejector handles at the same time, as shown in Figure 3. 3 Slide the CPU board out approximately one inch, then lift it straight up to remove...

  • Page 5: Removing Memory Modules

    Removing Memory Modules Removing Memory Modules 1 Locate the memory modules on the CPU board, as shown in Figure 4. Figure 4 Memory Module Location 2 To remove a memory module, push the ejector tabs on each side of the module. Lift the memory module up and out of the connector and place it on a static-free surface.
  • Page 6 Removing Memory Modules Figure 5 Removing a Memory Module...

  • Page 7: Installing Memory Modules

    Installing Memory Modules Installing Memory Modules 1 Locate the memory connectors on the CPU board, as shown in Figure 4 in the pre- vious section. 2 To install a memory module, close the ejector tabs on each side of the memory connector and line the memory module up with the guides, as shown in Figure 6.
  • Page 8 Installing the New CPU Board Installing the New CPU Board 1 Line up the CPU board with the main tray guides, as shown in Figure 7. Figure 7 Installing the New CPU Board Lower the CPU onto the guides, as shown in Figure 7. 3 Pull the two ejector handles so that they are fully open..

  • Page 9: Replacing The Main Tray Assembly

    Replacing the Main Tray Assembly Replacing the Main Tray Assembly 1 Align the main tray assembly with the chassis and slide it into place, as shown in Figure 7. Captive Screws Figure 8 Replacing the Main Tray Assembly 2 Slide the main tray in until you feel it make contact with the internal connectors. 3 Push firmly and evenly on the main tray assembly to make sure that all connec- tors are fully seated.
  • Page 10 Replacing the Main Tray Assembly 5 Replace the system unit in the floor stand, as shown in Figure 8. Figure 9 Installing the Floor Stand Reconnect the power cables and any other cables that you disconnected when opening the workstation. Power on the monitor, any peripheral devices, and the system unit.
  • Page 11 HP Part No. A4200-90011...

This manual is also suitable for:

Visualize c110

Table of Contents