Related Manuals for Hinkley ARTISTE
Summary of Contents for Hinkley ARTISTE
- Page 1 72" ARTISTE ™ INDOOR / OUTDOOR LED FAN DC MOTOR CEILING FAN INSTRUCTION MANUAL...
- Page 2 SO WE’RE HERE IF YOU HAVE A QUESTION, NEED SOME HELP OR WANT TO CHAT ABOUT OUR PRODUCTS. SEND SUGGESTIONS OUR WAY TOO—WE’RE ALWAYS LOOKING TO MAKE YOUR EXPERIENCE WITH HINKLEY A POSITIVE ONE. > SERVICE@HINKLEY.COM > 800.HINKLEY > LET’S SEE THAT HINKLEY STYLE @HINKLEY...
-
Page 3: Table Of Contents
INSTALLING THE HANGING BRACKET ENERGY GUIDE HANGING THE FAN SPECIFICATIONS ELECTRICAL CONNECTIONS SMART BY BOND FINISHING THE INSTALLATION INSTALLING THE BLADES WARNING: Read and follow these instructions carefully and be mindful of all warnings shown throughout. ©2019 Hinkley Lighting, Inc. | hinkley.com |... - Page 4 If the battery compartment does not close securely, stop using the product and keep it away from children. If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention. | hinkley.com...
-
Page 5: Important Safety Precautions
These factors must be supplied by the person(s) installing, caring for and operating the unit. TOOLS & MATERIALS REQUIRED • PHILLIPS SCREWDRIVER • FLAT SCREWDRIVER • WRENCH OR PLIERS • WIRE CUTTER • STEPLADDER • WIRING SUPPLIES AS REQUIRED BY ELECTRICAL CODE ©2019 Hinkley Lighting, Inc. | hinkley.com |... -
Page 6: Unpacking Your Fan
Remove all parts and hardware. Do not lay motor housing on its side, or the decorative housing may shift, be bent or damaged. • Examine all parts. You should have the following: ARTISTE PACKAGE CONTENT Blade Set of 3 BL900172Fxx... -
Page 7: Preparation
35 pounds. Attach hanging bracket to outlet box using screws provided with the outlet box. Flat Washer Spring Washer Outlet Box Screw Fig. 1 ©2019 Hinkley Lighting, Inc. | hinkley.com |... -
Page 8: Hanging The Fan
Tighten security set screws against downrod using a large (3) Wires flat blade screwdriver to ensure a tight fit against downrod. Tighten nuts against mounting collar. Downrod Security Screws Mounting Collar Cotter Pin Downrod Pin Top of Fan Body Fig. 2 | hinkley.com... - Page 9 Safety Cable Loop of the cable into the clamp and pull as much cable through as Wood Screw possible. Firmly tighten screw in the clamp. Cut off excess cable. And Washer Safety Cable Fig. 4 ©2019 Hinkley Lighting, Inc. | hinkley.com...
-
Page 10: Electrical Connections
Connect the WHITE receiver neutral wire to the WHITE building neutral wire. Connect the COPPER building ground wire to the 4 YELLOW/GREEN ground YELLOW wires from the fan and receiver. YELLOW GRAY Hanger bracket Receiver Fig. 1 Fig. 2 hinkley.com... -
Page 11: Finishing The Installation
Make sure the hook on the hanging bracket properly sits in the groove in the hanger ball before attaching the canopy to the bracket by turning the housing until it drops into place. ©2019 Hinkley Lighting, Inc. | hinkley.com |... -
Page 12: Installing The Blades
Use a large flat blade screwdriver for final tightening to fully compress the washers. This will help ensure proper alignment of the blades and noise-free, wobble-free running. Blades Blade support Screws plate | hinkley.com... -
Page 13: Installing The Light Kit And Glass Shade
Remove one of the three screws on the adapter plate Restore power and your light kit is ready for operation. located on the fan motor. Loosen the other 2 screws. (Do not remove) (Fig. 2) ©2019 Hinkley Lighting, Inc. | hinkley.com |... -
Page 14: Installing The Wall Control
Snap the face plate cover onto the wall bracket. Remote transmitter will be held in place with built in magnets. Cradle B Wall plate Plastic Face plate Outlet box anchor Transmitter Wall plate Cradle A Face plate Transmitter Wall Fig. 1 HIRO Control System Fig. 2 | hinkley.com... - Page 15 Attach the cradle A to the wall switch box using the supplied hardware. Attach the multi-gang faceplate to the switch set in the wall outlet box. Cradle A of Hinkley switch will fit in any standard decora face plate. Remote transmitter will be held in place with built in magnets.
-
Page 16: Operation
Even used cells may cause injury. many as 3 wall controls in one room. Every control will need to repeat the pairing process Fig. 2 based on instructions above and all controls must be within 30 feet of the fan. HIRO Control System | hinkley.com... - Page 17 An UPWARD airflow moves warmer air off the ceiling area as shown in Figure 4. This allows you to set your heating unit on a cooler setting without affecting your comfort. SUMMER MODE WINTER MODE (COUNTERCLOCKWISE DIRECTION) (CLOCKWISE DIRECTION) Fig. 3 Fig. 4 ©2019 Hinkley Lighting, Inc. | hinkley.com |...
-
Page 18: Care And Cleaning
If the blade wobble is still noticeable, interchanging two adjacent (side by side) blades can redistribute the weight and possibly result in smoother operation. Check to assure all dowrods to motor hardware and/or hanger ball are tight. Make sure ceiling box is secure. | hinkley.com... -
Page 19: Energy Guide
0.05 • Energy Use: 18 Watts All estimates based on typical use, excluding lights ftc.gov/energy RPMs Airflow Shown Is a Weighted Average of High and Low Cubic Feet per Minute Based on Downrod ©2019 Hinkley Lighting, Inc. | hinkley.com |... -
Page 20: Smart By Bond
SMART BY BOND HINKLEY SMART FAN OPTIONS: • Brute Force Method In addition to the included wall control, you can control your Hinkley fan a) Turn mains power OFF to the fan. through the Bond app. b) Turn mains power back ON on the fan. - Page 21 HINKLEY IS PROUD TO PROVIDE YOU WITH CEILING FAN PRODUCTS THAT ENHANCE YOUR SPACE WITH COMFORT, PURPOSE AND STYLE. AS A FAMILY COMPANY, WE ARE COMMITTED TO DESIGN, PERFORMANCE AND QUALITY, AND WHAT’S IMPORTANT TO YOU IS PARAMOUNT TO US.
- Page 22 GLOBAL HEADQUARTERS 33000 Pin Oak Parkway | Avon Lake, Ohio 44012 T (440) 653 5500 | F (440) 653 5555 | hinkley.com...