Table of Contents
Advertisement
Available languages
Available languages
Quick Links
700 SERIES
FILTERED FRESH AIR SUPPLY UNITS
OPERATION INSTRUCTIONS
PLEASE READ AND SAVE THESE INSTRUCTIONS
700 SERIES MODELS: 709, 710, 712, 715, 718
WARRANTY
CANARM Ltd. warrants every new product to be free of defects in material and workmanship, to the extent that, within a period of one
year from the date of purchase CANARM Ltd. shall either repair or replace at CANARM's option, any unit or part thereof, returned freight
prepaid, and found to be defective.
This warranty does not include any labour or transportation costs incidental to the removal and reinstallation of the unit at the user's
premises.Components repaired or replaced are warranted through the remainder of the original warranty period only.
This warranty applies to the original purchaser-user only; it is null and void in case of alteration, accident, abuse, neglect, and operation
not in accordance with instructions.
NOTICE:
No warranty claims will be honored by CANARM Ltd. unless prior authorization is obtained
GENERAL SAFETY
Rotating parts, (pulleys, shafts and belts) on fans should not be exposed. Where these components are not protected by ductwork, cabinets
or covers, appropriate guards should be employed to restrict exposure to rotating parts. Access doors should not be opened with the fan
operating to avoid foreign objects being drawn into the system. On initial start-up, a careful inspection should be carried out to ensure no
foreign material is present which could become airborne in the system.
Read installation and operation instructions carefully before attempting to install, operate or service Canarm/Delhi 700 Series. Failure to
comply with instructions could result in personal injury and/or property damage. Retain instructions for future reference.
Installation or Product problems? Do not return to store of purchase.
Contact Canarm Service at 1-800-265-1833 (CANADA) 1-800-267-4427 (U.S.A.)
1-800-567-2513 (EN FRANCAIS) Monday to Friday 8:00 - 5:00pm e.s.t.
700 SERIES_06_14_2022
MODEL
MAX. HP
709
1.5
710
1.5
712
2
715
3
718
5
SHAFT
WEIGHT
DIAMETER
3/4"
155 lbs
3/4"
204 lbs
3/4"
247 lbs
1"
267 lbs
1"
370 lbs
.
Page 1 of 4
Advertisement
Table of Contents
Related Manuals for Canarm 700 Series
Summary of Contents for Canarm 700 Series
- Page 1 WARRANTY CANARM Ltd. warrants every new product to be free of defects in material and workmanship, to the extent that, within a period of one year from the date of purchase CANARM Ltd. shall either repair or replace at CANARM’s option, any unit or part thereof, returned freight prepaid, and found to be defective.
-
Page 2: Before You Begin
700 SERIES FILTERED FRESH AIR SUPPLY UNITS BEFORE YOU BEGIN Inspect unit for damage, report any shipping damage to carrier. Check all fasteners, re-tighten as required. Rotate the blower wheel by hand to ensure free rotation. If rubbing occurs, loosen the set screw(s), re-position the wheel to the shaft center, re-tighten set screws. -
Page 3: Pulley Alignment
700 SERIES FILTERED FRESH AIR SUPPLY UNITS WARNING EXCESSIVE BELT TENSION IS THE MOST FREQUENT CAUSE OF BEARING WEAR AND RESULTING NOISE. PROPER BELT TENSION IS CRITICAL FOR QUIET EFFICIENT OPERATION. Ideal belt tension is the lowest value under which belt slip will not occur at peak load conditions. -
Page 4: Operation
7. To reinstall replacement ball bearings press the locking collar against the inner ring of the bearing and turn in the direction of the shaft rotation until engaged. Insert a drift pin into the pin hole and tap lightly to set. Tighten set screw on locking collar firmly (see Figure 4). Canarm Ltd. - Corporate Head Office 2157 Parkedale Avenue, PO Box 367 Brockville, Ontario Canada K6V 5V6 Tel: (613) 342-5424;... - Page 5 Lisez les instructions d’installation et d’opération attentivement avant d’effectuer l’installation, l’opération ou la maintenance des ventilateurs de la série Canarm/Delhi 700 Sèries ou Canarm/Delhi IDB. Le non-respect des instructions peut entraîner des blessures et/ou des dommages matériels. Conservez les instructions pour référence future.
-
Page 6: Avant De Débuter
SÉRIES 700 UNITÉS D’APPROVISIONNEMENT D’AIR FRAIS FILTRÉ AVANT DE DÉBUTER Inspectez l’unité pour détecter tout dommage et rapporter tout dommage causé par le transport au transporteur. Vérifiez toutes les fixations, resserrez si nécessaire. Faites tourner la roue du ventilateur à la main pour assurer une rotation libre. En cas de frottement, desserrez-la ou les vis de réglages, repositionnez la roue au centre de l’arbre et resserrez les vis de réglage INSTALLATION Calfeutrez le dessus de la bordure. - Page 7 SÉRIES 700 UNITÉS D’APPROVISIONNEMENT D’AIR FRAIS FILTRÉ Longueur de la courroie Moteur Ventilateur MODÈLE SOUFFLEUR basée sur le Poulie Fonte Poulie Intervalle châssis du Fonte moteur HB47T 1630 - 1232 ---- ---- MODÈLE HB57T 1329 - 1005 ---- ---- HB67T 1121 - 848 ---- ----...
-
Page 8: Entretien
Insérez une goupille et tapotez légèrement pour régler. Serrez fermement la vis de réglage sur le collet de verrouillage (voir Figure 4). Canarm Ltd. - Siège Social 2157 Parkedale Avenue, PO Box 367 Brockville, Ontario Canada K6V 5V6 Tel: (613) 342-5424;...