Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Hausmann 1396
Summary of Contents for Hausmann 1396
- Page 1 130 UNION STREET, NORTHVALE, NJ 07647 Ph: (201) 767-0255 Fax: (201) 767-1369 CSDept@hausmann.com Models 1396 and 1398 Operation and Service Guide Model 1396 (Less dowel holes and apparatus) Model 1398 (With dowel holes and apparatus) 11/3/04 2004 Hausmann Industries, Inc.
-
Page 2: Table Of Contents
Models 1396, 1398 Power Height Parallel Bars Operation and Service Guide TABLE OF CONTENTS Construction ........................Page 1 Lifting Columns ......................... Page 1 Control Box ........................Page 1 Hand Switch ........................Page 2 Operating Method ......................Page 2 Technical Data ........................ -
Page 3: Hand Switch
NOTE: Handrail motors are designed to electrically adjust in height , and to be stable under use when at their fixed height level. Motors are not designed to "lift" full weight of patient from sitting to standing position. 2004 Hausmann Industries, Inc. 11/03/04... -
Page 4: Operation
After the position key has been pressed, the number of the position key appears in the LED display next to S. After the memorization procedure, a double-click is heard, and after approximately 2 seconds the current height appears again in the LED display. 2004 Hausmann Industries, Inc. 11/3/04... -
Page 5: Positioning To Memorized Position
Responsibility for the operation of the apparatus falls in all cases on the proprietor or operator, if the apparatus has been improperly installed , maintained or adjusted, or if use is made of it which does not correspond with its intended use. 2004 Hausmann Industries, Inc. 11/3/04... -
Page 6: Wiring Diagram
1396/1398 WIRING DIAGRAM ALL CORD CONNECTIONS FROM LIFT COLUMNS TO CONTROL BOX ARE PRE-CONNECTED AT FACTORY. DO NOT REMOVE CONNECTIONS WITHOUT FACTORY AUTHORIZATION. Lift Motor Lift Motor Lift Motor Lift Motor Column 4 Column 3 Column 2 Column 1 # TMA... -
Page 7: Model 1396 And 1398
MODEL 1396 AND 1398 (1396 has no dowel holes in platform) 10' Stainless Steel Handrails Control Panel Manual with LED display Width of height of bars Controls 27" Clearance (in inches) between uprights (4) "TMA" Powerlift Columns 110V Power Cord... -
Page 8: Detail Of Hand Control Switch
TMA Lift Column to Control Box (See wiring diagram on page 5) Wood Platform (Shown with #1398 Cord Connection dowel holes - #1396 to Control Box has no dowel holes) (See wiring diagram on page 5) 2004 Hausmann Industries, Inc. 11/3/04... -
Page 9: Detail Of Control Box
Do not open or access control box without prior factory authorization. Disconnect 110V power cord before authorized access. Control Box Lid Removed LD-014 Port 4 Port 3 Port 2 Port 1 Control Switch Port Control Box (shown with lid "off") 2004 Hausmann Industries, Inc. 11/3/04... -
Page 10: Detail Of Width Adjustment Knob
"out" as needed, and retighten friction control knobs to lock-in width position of handrails. Width adjusts from 15" to 28" wide. Each side should be adjusted at the same time. See image below: Adjust side A-B, then adjust side B-C. 2004 Hausmann Industries, Inc. 11/3/04... -
Page 11: Model 1398 Only
Control box with lid in place (Do not remove lid without factory authorization.) Detail of dowel pin of balance beam. Position dowel pins on each end of balance beam in center row of dowel holes before use. 2004 Hausmann Industries, Inc. 11/3/04...