Related Manuals for Idex Knight Ultra Micro-Pro UMP 100 Series
Summary of Contents for Idex Knight Ultra Micro-Pro UMP 100 Series
- Page 1 Ultra Micro-Pro UMP 100 / 200 Series Instruction Manual 0901082 Rev: D (08/08) Page 1 of 12...
-
Page 2: Table Of Contents
TABLE OF CONTENTS Declaration of Conformity ..................3 Introduction ......................4 Circuit Board Diagram...................4 Installation......................5 Plumbing.......................5 Probe Installation ....................6 Electrical .......................6 Rinse Operation ....................7 Probe Operation....................8 Probeless Operation .....................9 Wiring Diagram ....................10 Assembly Diagram....................11 Warranty Information ..................12 Knight Locations ....................12 EQUIPMENT RATINGS This includes equipment supply, description of I/O connections, duty cycle and operating environmental conditions. -
Page 3: Declaration Of Conformity
0901082 Rev: D (08/08) Page 3 of 12... -
Page 4: Introduction
INTRODUCTION Ultra Micro-Pro UMP-Series warewash systems provide the versatility of probe or probeless detergent control through advanced microprocessor design. With the capability of controlling up to two products, and the choice of liquid or dry detergent, virtually any warewash application can be accommodated. The UMP Series warewash control features simplicity and versatility. -
Page 5: Installation
PRESSURE SWITCH PLUMBING (optional) INSTALLATION Install pressure switch kit. Thread the male end of the Mount the unit (using suitable hardware) with the “tee” fitting into the rinse line on the dishwasher, and provided bracket in the accessory kit. Try to keep the connect the poly tubing from the rinse pump into the end unit within three feet from the final rinse line to avoid opposite the male threads, using the checkvalve... -
Page 6: Probe Installation
PROBE INSTALLATION (if required) DETERGENT POWER SIGNAL (1) Install the probe in the wash tank below the water A detergent power signal is required to activate the level. It should be away from incoming water detergent probe sensing or probeless initial charge. supplies, near the recirculating pump intake, and 3 Detergent power can be jumpered from main power. -
Page 7: Rinse Operation
RINSE OPERATION The rinse pump will operate whenever the rinse power signal is applied to the circuit board, whether directly from the dishwasher, or by using a pressure switch. A rinse delay feature and rinse limit feature maximize the operating capabilities of the rinse pump. A prime button, located on the front cover, will allow the rinse pump to run at full speed, regardless of the rinse potentiometer setting. -
Page 8: Probe Operation
PROBE OPERATION • With the detergent power “on”, the conductivity probe senses detergent concentration. When concentration drops below the setpoint, the control automatically turns on detergent feed. Low and high concentration ranges allow easy setting • on all types of water conditions. SLIDE LEFT TO ACTIVATE When the detergent concentration is within 15% of the •... -
Page 9: Probeless Operation
PROBELESS OPERATION • Controls detergent concentration without a probe, based on timed detergent feed. • Initial charge time feeds detergent concentration setpoint when dishmachines are initially filled. • Recharge time feeds detergent to maintain detergent SLIDE RIGHT TO ACTIVATE setpoint as rinse water dilutes the dishmachine. •... -
Page 10: Wiring Diagram
WIRING DIAGRAM Page 10 of 12 0901082 Rev: D (08/08) -
Page 11: Assembly Diagram
ASSEMBLY DIAGRAM 0901082 Rev: D (08/08) Page 11 of 12... -
Page 12: Warranty Information
Knight, LLC reserves the right, however, to discontinue or change specifications or design at any time without notice and without incurring any obligation whatsoever. KNIGHT LLC, KNIGHT LLC, KNIGHT LLC, KNIGHT LLC, A Unit of IDEX Corporation (www.knightequip.com) Knight Headquarters USA Toll Free Knight Canada Knight Europe Knight Australia Knight N.