Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for ISYGLT LS-06-PIR-02-WH
Summary of Contents for ISYGLT LS-06-PIR-02-WH
- Page 1 Technical Data / Instruction Manual LS-06-PIR-xx-WH-xx Article no. 8008507x-xx Light and PIR Motion Sensor (passive infrared) Seebacher GmbH www.seebacher.de Phone: +49 (0) 80 41 / 77 77 6 Marktstrasse 57, 83646 Bad Tölz info@seebacher.de Fax: +49 (0) 80 41 / 77 77 2...
-
Page 2: Notes On Documentation
These instructions are intended for qualified personnel who are 1. Notes on documentation familiar with the assembly, installation and operation of the ISYGLT system. It is essential that you read these operating instructions through before commissioning and keep them accessible for further 1.1. -
Page 3: Safety Instructions
• ponents with tested standard plug connections, as well as operation Use module indoors only • and configuration of the ISYGLT module may only be carried out by Protect module from humidity • trained staff. In addition to these safety instructions, you must also observe... -
Page 4: Warranty
These are limited to the intended use of the module and refer EU on waste electrical and electronic equipment at the local collec- to the repair or replacement of the ISYGLT module. Please send the tion points for waste electrical and electronic equipment! device with an attached error description to our company address given below. -
Page 5: Product Description
The sensor is connected directly to the are individually possible, such as activating the lighting only in the case ISYGLT BUS. The light sensor provides a calibratable 16-bit brightness of large movement or maintaining the „ON“ state even in the case of value. - Page 6 Subnet BUS B 10.2. Address setting Due to its design, the sensor does not provide space for the usual DIP switch for address setting. At this sensor, the address is set via software parameterisation with the ISYGLT ProgramDesigner. 10.3. Function displays State...
- Page 7 In the ProgramDesigner (from version 8.00.13.1002 R095) the sensor must be created as a module. Additionally a virtual module „ISYGLT_ADR“ is required. To set the BUS address, the desired address must be entered in the register Parameter. Now the sensor to be addressed must be put into addressing mode - the red LED now flashes quickly. Click on „Sende Parameter“...
- Page 8 10.4. View LS-06-PIR-01-WH-APG LS-06-PIR-01-WH-UP LS-06-PIR-01-WH LS-06-PIR-02-WH-APG LS-06-PIR-02-WH-UP LS-06-PIR-02-WH Mini housing Seebacher GmbH www.seebacher.de Phone: +49 (0) 80 41 / 77 77 6 Marktstrasse 57, 83646 Bad Tölz info@seebacher.de Fax: +49 (0) 80 41 / 77 77 2...
- Page 9 11. Detection ranges PIR sensor types LS-06-PIR-01-WH-xx Low Profile Type Detection area: 110° x 110° Typical mounting height: 3m Range: up to 5m Seebacher GmbH www.seebacher.de Phone: +49 (0) 80 41 / 77 77 6 Marktstrasse 57, 83646 Bad Tölz info@seebacher.de Fax: +49 (0) 80 41 / 77 77 2...
- Page 10 LS-06-PIR-02-WH-xx Standard + Slight Motion Detection area (Slight Motion): 44° x 44° Detection area (Standard Motion): 91° x 91° Typical mounting height: 3m Range: 2.2m - 3.1m Seebacher GmbH www.seebacher.de Phone: +49 (0) 80 41 / 77 77 6 Marktstrasse 57, 83646 Bad Tölz info@seebacher.de...
- Page 11 12. Wiring diagram +24V BUS-A BUS-B BUS address Light / PIR motion sensor LS-06-PIR-xx-xx Art. no.: 8008507x Misprints and technical changes reserved. Seebacher GmbH www.seebacher.de Phone: +49 (0) 80 41 / 77 77 6 Marktstrasse 57, 83646 Bad Tölz info@seebacher.de Fax: +49 (0) 80 41 / 77 77 2...
Need help?
Do you have a question about the LS-06-PIR-02-WH and is the answer not in the manual?
Questions and answers