Subscribe to Our Youtube Channel
Related Manuals for milliard Art Table
Summary of Contents for milliard Art Table
- Page 1 Art Table Congratulations on the purchase of your Art Table PRECAUTION: Always read and follow instructions before use | Always use the unit according to the manufacturers guidelines | Only use the unit in a manner as intended by manufacturer.
-
Page 2: W E ' Re H E R E To H El P
TIMES IN ACCORDANCE TO FEDERAL AND LOCAL LAWS OR REGULATIONS. BUYER ASSUMES ALL RISKS AND LIABILITY FROM MISUSE OF THIS PRODUCT AND MILLIARD SHALL NOT BE HELD LIABLE BEYOND THE INITIAL PURCHASE COST OF THE PRODUCT FOR ANY DAMAGES ARISING FROM ITS MISUSE. - Page 3 C H A I R PA RTS Left Chair Right Chair Seat Back x2 Seat Support x4 Seat x2 Side ×2 Side ×2 TABLE PARTS Left Table Leg Table End Right Table Leg Left Side Panel Right Side Panel Center Support Easel End Table Bottom Support...
- Page 4 Canvas Holder x2 Rod Support x2 Knob x4 Paper Roll Cup x5 Storage Bin x6 Bin Insert x6 HARDWA R E Dowel Nut x36 Medium Bolt x30 Wooden Dowel x30 Round Head Screw x2 Long Bolt x6 Flathead Screw x6 Cam Nut x10 Cam Screw x10 Short Bolts x6...
- Page 5 ASSEMBLY INSTRUCTIONS Start by assembling the chairs. STEP 1 Insert wooden dowels into each of the six shallow holes on the left chair side . STEP 2 Insert a dowel nut into the hole on the seat and attach it to the left chair side with a medium bolt .
- Page 6 STEP 4 Insert wooden dowels into each of the six shallow holes on the right chair side . STEP 5 Insert dowels nuts into the holes of the seat back , seat and seat supports and attach the right chair side with medium bolts Now, let’s assemble the table.
- Page 7 STEP 7 Let’s attach the left and right table legs to the table end by inserting long bolts . STEP 8 • Place dowel nuts wooden dowels into the center support • Insert dowel nuts into the easel end support STEP 9 Attach the left and right side panels to the center support...
- Page 8 STEP 10 Slide the table bottom into the slots on side panels until it 9 10 fully rests in the slot on the easel end support . Make sure that the indented corners are facing the open side. STEP 11 •...
- Page 9 STEP 12 Place dowel nuts into the middle and bottom shelves 16 17 STEP 13 Attach the right and left shelf sides to the bottom shelf 14 15 using medium bolts . STEP 14 Slide in the bottom shelf back . STEP 15 Attach the middle shelf using...
- Page 10 STEP 16 Slide in the upper shelf back . Make sure that the indented corners are facing up/the open side. STEP 17 • Insert cam nuts into the right and left shelf sides 14 15 • Insert cam screws into the shelf top .
- Page 11 STEP 19 With the shelf unit still upside-down, insert the protruding ends of the partially constructed table through the openings in the back of the shelf unit and secure with short bolts on each side as shown. Now, let’s assemble the tabletop. STEP 20 •...
- Page 12 STEP 21 • Insert cam screws into the holes on the cup holder panel as shown. • Insert a cam nut into the smaller hole of one of the rod supports and secure it to the table top by turning the cam nut clockwise 90 degrees.
- Page 13 STEP 23 • Attach the rod to the second rod support using a round head screw • Insert a cam nut into the other rod support and secure it to the table top by turning the cam nut clockwise 90 degrees.
- Page 14 STEP 25 Attach the protruding side of the pneumatic pistons to the underside of the desktop with short flathead screws . STEP 26 Attach the flat side of the pneumatic pistons to the inside of the side panels with short flathead screws . 9 10...
- Page 15 STEP 27 Gently attach the canvas holder strips to the table top with the knobs . STEP 28 • Finally, place the cups in the cup holders. • Insert the bin inserts into the bins and place the bins onto the storage shelves. Now, let’s make some art together!
Need help?
Do you have a question about the Art Table and is the answer not in the manual?
Questions and answers
The pneumatic piston does not slide up or down so we can’t open and close the top of the Millard art table
To fix a pneumatic piston that does not slide on the Millard Art Table, check the following:
1. Ensure the piston is correctly attached:
- The protruding side of the piston should be attached to the underside of the desktop using short flathead screws.
- The flat side of the piston should be attached to the inside of the side panels using short flathead screws.
2. Verify that all screws are securely fastened and properly aligned.
3. Make sure there are no obstructions or debris around the piston mechanism.
4. Do not force the piston; if it remains stuck, it may be defective and require replacement.
If these steps do not resolve the issue, contact customer support for assistance.
This answer is automatically generated