ECOVACS WINBOT 920 Instruction Manual
  1. Manuals
  2. Brands
  3. ECOVACS Manuals
  4. Cleaning Equipment
  5. WINBOT 920
  6. Instruction manual

ECOVACS WINBOT 920 Instruction Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Instruction Manual

Advertisement

Table of Contents
loading

Related Manuals for ECOVACS WINBOT 920

Summary of Contents for ECOVACS WINBOT 920

  • Page 1 Instruction Manual...

  • Page 2: Important Safety Instructions

    Important Safety Instructions 3. Do not use this product in whole gale storms and When using an electrical appliance, basic force-10 winds, or in areas where the altitude precautions should always be followed, including exceeds 2000 meters(6162 feet). the following: 4.
  • Page 3 to the glass or has visible signs of damage. 21. The plug must be removed from the receptacle 14. To reduce the risk of electrical shock, do not put before cleaning or maintaining the Appliance. the Appliance in water or other liquid. Do not Do not unplug the Power Adapter by pulling on place or store Appliance where it can fall or be the power cord.
  • Page 4 29. The robot contains batteries that are only replaceable by skilled persons. For EU Declaration of Conformity information, visit 30. The plug and the Power Adapter must be used https://www.ecovacs.com/global/compliance indoor. To satisfy RF exposure requirements, a separation distance of 20 cm or more should be maintained between this device and persons during device operation.

  • Page 5: Package Contents

    Package Contents Product Diagram WINBOT Status Indicator Light/START/ PAUSE Button WINBOT+ Safety Tether Power Adapter and Carabiner Bumper Rail Instruction Manual Bottom View Instruction Manual Finishing Cloth Edge Detection Sensors Side Rollers Power Switch Driving Treads WINBOT Cleaning Cleaning Pads Bottom Status Solution Indicator Light...

  • Page 6: Notes Before Cleaning

    Notes Before Cleaning Make sure Safety Tether and Carabiner have been connected with WINBOT before using. (Connected by default. Do not disconnect before cleaning.) Note: Do not use WINBOT on a framed window with a frame narrower than 5 mm(0.2”).

  • Page 7: Quick Start

    ECOVACS HOME App Preparation before Use To enjoy all available features, it is recommended to control your Properly Tether WINBOT to a Safe Place WINBOT via the ECOVACS HOME App. • Deep Cleaning Mode • Spot Cleaning Mode • Switching Interior/Exterior Window...
  • Page 8 It is recommended to use WINBOT with WINBOT Cleaning Solution Wipe the area for WINBOT to safety attach to. from ECOVACS. Using tap water or other cleaners could have an Place WINBOT on the window at least 10cm (4”) from window corners adverse effect on cleaning performance.
  • Page 9 Power Off Pause Unfasten Safety Tether Finish Remove WINBOT Unplug WINBOT...

  • Page 10: Maintenance

    Washing the Cleaning Pad regularly can extend its service life. If the Cleaning Pad becomes worn or no longer fits exactly within the fastener area, replace it with a new one to achieve optimal cleaning performance. Explore more accessories at https://www.ecovacs.com/global.

  • Page 11: Driving Treads

    Driving Treads Note: Inspect the Driving Treads in ECOVACS HOME App. Stop the Driving Treads if you see dirt on them. Edge Detection Sensors Side Rollers * After WINBOT has a low battery alarm, be sure to fully charge it before using or storing it to avoid reducing the battery life.

  • Page 12: Status Indicator Light

    Status Indicator Light Light Effect Status WINBOT is fully charged. WINBOT has successfully adhered itself to the glass and is ready to clean. Status Indicator glows a continuous BLUE. WINBOT is cleaning. WINBOT is paused. The network setup is complete. Status Indicator flashes BLUE slowly.

  • Page 13: Troubleshooting

    Hold the Safety Tether or the Power Cord. Meanwhile, press Direction be cleaned. move. Buttons in ECOVACS HOME App to let the WINBOT leave the gap or The cleaning pad plate is blocked by barrier. small obstacles on the glass.
  • Page 14 10cm/4” from window corners and obstacles. Restart WINBOT. Fix the Safety Clasp and tether firmly. Hold WINBOT power cord and meanwhile, use ECOVACS HOME App to move WINBOT away from WINBOT is stuck. It is stuck by obstacles.

  • Page 15: App Connection

    6. Bluetooth may be disconnected if WINBOT is too distant from the phone. Try to reconnect at a short distance. 7. For using WINBOT, you need to allow ECOVACS HOME App to obtain access to the location, Bluetooth, and mobile phone storage.
  • Page 16 Ecovacs Home Service Robotics Co., Ltd. No. 518 Songwei Road, Wusongjiang industry Park, Guoxiang Street, 451-2005-0301 Wuzhong District, Suzhou, Jiangsu, China.

This manual is also suitable for:

Wg811

Table of Contents