Related Manuals for Sanus CFR2100 Series
Summary of Contents for Sanus CFR2100 Series
- Page 1 CFR2115, CFR2127, CFR2136, CFR2144 Instruction Manual We’ll Make It Stress-Free If you have any questions along the way, just give us a call. 1-800-359-5520. We’re ready to help! Scan for more information san.us/891...
- Page 2 IMPORTANT SAFETY INSTRUCTIONS – SAVE THESE INSTRUCTIONS PLEASE READ ENTIRE MANUAL PRIOR TO USE Thank you for choosing a Sanus Component Series Rack. The CFR2100 series is designed to support audio/video equipment. The total weight capacity for the CFR2100 series: CFR2115 226.8 kg (500 lb)
-
Page 3: Parts And Hardware
Parts and Hardware CFR2115 CFR2127 CFR2136 CFR2144 CFR2115 CFR2127 CFR2136 CFR2144 M5 x 10 mm 10-32 x 3/4 in. CFR2115 CFR2115 CFR2127 CFR2127 CFR2136 CFR2136 CFR2144 CFR2144... - Page 4 Load Your Components CAUTION: Failure to follow loading requirements could lead to instability causing personal injury and/or property damage: To prevent instability: • Always load the rack from the bottom up and load the heaviest item first. • 50% of the total weight should be mounted in the lower 1/3 of the rack.
- Page 5 Load Your Components CAUTION: Failure to follow loading requirements could lead to instability causing personal injury and/or property damage: To prevent instability: • Always load the rack from the bottom up and load the heaviest item first. • 50% of the total weight should be mounted in the lower 1/3 of the rack. •...
- Page 6 Using Backstops and Component Straps Rack Shelf Backstops NOTE: rear view with back panels removed. Insert backstop into slot behind component. Slide backstop forward until firmly against component and twist 90 degrees. Component Straps NOTE: side view with panels removed. A.
- Page 7 Access Panels for Cable Management...
- Page 8 Install Fan for Additional Ventilation (Top or Bottom) CAUTION: Avoid damage to your components due to overheating. Make sure that there is adequate space between each unit for proper airfl ow. Operating temperature inside the rack must not exceed 104°F (40°C). To install fan: Remove the vented panel.
- Page 9 Adjust Shelves and Blanking Panels NOTE: Align the bottom of the shelf or blanking panel with the lines on the rack rail.
- Page 10 Adjust Rack Rails Remove the shelves and blanking panels before adjusting the rails. Adjust the right and left rails evenly. NOTE: For clarity, the front door, top, and side panels are not shown.
- Page 11 Switch Back Panels Remove large upper panel. Remove small lower panel and frame. Fit bottom of large panel into rack frame and angle the panel up until sliding locks snap in place. Flip small panel 180 degrees. Screw panel frame into rack frame and replace small panel.
- Page 12 Reverse the Front Door Remove the door Turn upper door pin to release from locking tab and pull down to release door from rack and lift door from rack frame. Release upper pin and turn it back to secure it with the locking tab.
- Page 13 Reverse the Front Door - continued Flip the door Fit spacer onto bottom pin and fit bottom pin into bottom mounting hole in rack. Turn upper pin to release from locking tab and pull down. Fit pin into upper mounting hole in rack. Release pin and turn pin to secure it with locking tab.
- Page 14 Reverse the Front Door - continued Flip the door Remove screws and bracket. Flip the door handle. Reattach screws and bracket. Loosen the locking cam screw. Tighten the locking cam screw. Flip the locking cam tab to the side nearest the edge of the door.
-
Page 15: Manage Cables
Add Keyed Lock to Door (Sold Separately) Install keyed lock (purchased Remove plug from side panel. separately) in plug hole. Manage Cables... - Page 16 Ganging Racks (Ganging Kit Sold Separately) Move racks together until sides are Remove side panels on sides to be touching. connected. IMPORTANT Make sure both racks are level with each other. Fit four ganging clips (GC) into frame slots. Press down on clips to secure. IMPORTANT Make sure all four ganging clips are fully engaged.
- Page 17 Level Feet Adjust the feet to level the rack. Tighten nuts until they are flush with the bottom of the rack. CAUTION: To avoid potential injury or property damage, always ensure that your rack is level.
- Page 18 Thank you for choosing Sanus! Please take a moment to let us know how we did: Call us: 1-800-359-5520 UK: 0800 056 2853 Email us: info@sanus.com Leave a review: sanus.com Milestone AV Technologies and its affi liated corporations and subsidiaries (collectively, “Milestone”), intend to make this manual accurate and complete.
- Page 19 COMPONENT SERIES AV RACKS Introducing the SANUS 100 Series Racks – the Second Generation The engineers at SANUS took the Component Series racks to the next level with the SANUS 100 Series Racks – the Second Generation. Constructed of heavy-gage welded steel, the 100 Series come pre-assembled with vented shelves and blanking panels to simplify ordering and installation.
- Page 20 ® SANUS FOUNDATIONS COMPONENT SERIES AV RACKS MODEL: CFR2115 MODEL: CFR2127 DESCRIPTION DESCRIPTION 15U AV Rack 27U AV Rack DIMENSIONS (W X D X H) DIMENSIONS (W X D X H) 23.6" x 23.6" x 34" / 60 x 60 x 86.4 cm 23.6"...
Need help?
Do you have a question about the CFR2100 Series and is the answer not in the manual?
Questions and answers