Advertisement

Quick Links

PHASE EIGHT@
INSTRUCTIONS FOR
INSTALLATION AND OPERATION
CONTROLS FOR MOTORIZED
ZOOM LENSES
VlOOC, VlOOZF
MODEL
GENERAL
SCOPE
The information in this instruction manual
covers the installation, operation, and
maintenance of the following lens controls:
VlOOC
VlOOZF
These units should be installed using approved
materials and wiring practices in accordance
with the National Electrical Code and
applicable local wiring ordinances.
INTRODUCTION
This series of motorized zoom lens controls
enables remote operation of most Vicon zoom
lenses, including those with internal
electronic autoiris
circuitry. On each model,
circuit interlock prevents damage that could
occur when buttons for opposing functions are
pushed simultaneously. Speed control is
accomplished by a panel-mounted potentiometer
and internal range compensation.
These rugged controls are housed in the
compact PHASE EIGHT* module and contain
durable solid-state circuitry. PHASE EIGHT
modules may either be rack-mounted or
installed in desk-top units. The VP8RK Card
Cage is designed to fit in a standard 19-inch
rack. The VP8RK holds any combination of
single-, double-, or triple-size modules
totaling eight positions. When desk-top
WARNING: TO PREVENT RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THESE UNITS TO RAIN OR MOISTURE.
Product Specifications subject to change wthout nof~ce
AND V108C
525 BROAD HOLLOW ROAD, MELVILLE. N.Y. 11747 TEL: (516) 293-2200 TELEX: 144581
TOLL
FREE:
800-645-9116
REF. NOTES
SUPERSEDES
X104-386
VlOOC LENS CONTROL
installations are desired, the V4DTB and V8DTB
are available with four and eight positions,
respectively. (See Associated Equipment and
Accessories for variation.)
Model VlOOC may be used with any Vicon
motorized zoom lens (indicated by the suffix M
in the part number) or with an Intraspot* lens
(suffix MS) when manual operation of the iris
is required.
Model VlOOZF is used both with motorized
zoom lenses (suffix AC or SND), which feature
internal autoiris
circuitry,
not requiring iris control.
Model VlOSC is identical to Model VlOOC
except that it provides circuitry for control
of zoom lenses having a built-in motorized
extender (suffix MSX).
All models operate lenses up to the distances
shown in Table 1.
Vicon
*Registered
Trademarks
Patent
pending
(OUTSIDE OF NEW YORK)
SHEET NO. REV.
SEC.
X104 687
and
with cameras
part
number
8006-9104-02-00
of
Vicon
Industries
Inc.
on
PHASE
EIGHT.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the VlOOC and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Vicon VlOOC

  • Page 1 Accessories for variation.) INTRODUCTION This series of motorized zoom lens controls Model VlOOC may be used with any Vicon enables remote operation of most Vicon zoom motorized zoom lens (indicated by the suffix M lenses, including those with internal...
  • Page 2 Model VSDTB-2: Accepts PHASE EIGHT TABLE I CABLE DISTANCES modules up to a total of eight positions for desk-top use. Supplied with a rear cover which conceals cables to the PHASE EIGHT Maximum Distance** modules. Includes the VPSRK Card Cage. Wire Size (AWG) For Voltage Output Annealed Copper...
  • Page 3 Never spill liquid of any kind on the control. 6. Attachments - Do not use attachments not recommended by Vicon, as they may cause 15. Servicing - Do not attempt to service hazards. the control yourself, as opening or removing covers may expose you to dangerous voltage or 7.
  • Page 4: Installation

    3). Also refer to the specific instruction PHASE EIGHT CARD CAGE OR DESK-TOP ENCLOSURE CAUTION: Do not change the settings of Vicon motorized lenses manually. To avoid To install a control module into a PHASE mechanical damage, use the proper control to EIGHT Card Cage or Desk-Top Enclosure, energize the lens.
  • Page 5: Operation

    The medium and high voltage settings provide RETAINING an increase in voltage to the lens unit for CONNE BRACKET applications requiring higher voltage output. CAUTION: Under no circumstances should the voltage be set for a higher output level than needed for the distances specified in Table I, which are based on the use a V20-IOOA-M lens receiving a constant 5 V at 100 mA, stall...
  • Page 6: Shipping Instructions

    2. Include the RA number, the name of the person who return a unit to Vicon. issued the number, and your company’s name and address with your returned unit. The Vicon RA number If a unit must be returned to the factory: MUST appear on any correspondence concerning the...
  • Page 7 N O T E S : ALL COMP. USED. 2. FOR MODEL VlOOC CRZ, CR& Rl9, SW1 NOT USED. 3. FOR MODEL VlOOZF CR2 THRU CR’I,QZ,Q3, R6, R7. R6,...
  • Page 8 FOCUS NAR IRIS CPEN I R I S C L O S E NOTES: 1. FOR MODEL V108C ALL COMP. USED. 2. FOR MODEL VlOOC CR2, CRS, RlQ, AND SW1 NOT USED. 3. FOR MODEL VlOOZF CR2 THRU CR7, NOT USED.
  • Page 9 n - l Figure 7 Parts Location Diagram Lens Controls, Main Board...
  • Page 10 REPLACEMENTPARTS LIST REFERENCE PART DESCRIPTION DESIGNATION NUMBER Assembly PC Board 1233-3175-04 8002-8118-00 Rectifier PD-20 or FW200 Mallory or Int’l Ret 2KBP02 1913-3000-02 Flexible Flat Conductor Jumper Assembly .lO Centers Capacitor .470uF 50 V Z5U 1802-0032-65 Cl ,c3 Capacitor 470uF 35 VDC Electric Capacitor 1 uF 50 VDC Ceramic 10 1802-0027-73 1802-0005-06...

This manual is also suitable for:

VloozfV108c

Table of Contents