Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Netum DS2800
Summary of Contents for Netum DS2800
- Page 1 Package Included: 1 *Scanner; 1 * Power Charging Dock; 1 * USB Cable; 1 * Quick Setup Guide V2.7.15 Note: This is a general manual. If you need more coni�igurations please download it from our of�icial website: https://www.netum.net/...
-
Page 2: Product Information
Product Information: Scanning Window Module Bluetooth light / Battery light Reading indicator light Beeper (Green / Blue / Red) Indicator light Power button ON/OFF Data Receiver Dock / Charg Dock Type-B Type-A USB Cable... -
Page 3: Firmware Version
Firmware Version: $SW#VER Get Version Connect charge cradle with your host through USB cable (provided by Netum) or Charge the scanner take a DC plug and charge it on an electrical wall outlet. Then plug scanner on the charge cradle to charge power for it. -
Page 4: Factory Defaults
Scanner will power off after you scanning Factory Restore. %#IFSNO$B Factory Restore Netum barcode scanners are factory programmed for the most common terminal and Barcode Programming: communication settings. If you need to change these settings, programming is accomplished by scanning the barcodes in this guide. An asterisk (*) next to an option... - Page 5 Some command barcodes only work in a particular connection mode. Important Notes : Please pay attention to below symbols before you scanning the command barcodes. Command barcodes only apply to scanner transmit characters via Bluetooth. Command bacodes only apply to scanner transmit characters via Wi�i. Connection Way Scanner transmits characters to your device via bluetooth or Wi�i.
- Page 6 4) Open “Netum Wi�i service.exe” to �ill in all blanks. (Only do it in the �irst time.) 5) A QR code will be generated after you �illing all required information. 6) Scan the QR code and close “Parameter Con�iguration” window.
- Page 7 8) Once scanner connected with wi�i and the software successfully , below notice will be displayed in the software. Restart the software Restart: Open con�iguration interface. Con�igure: 9) Click “Keyboard entry” and” Open URL”. 10) Locate cursor on the place where you want scanner to output characters. 11) Setup keyboard language(please refer to the part of”...
-
Page 8: Important Notes
Get Started: (1)Power on scanner. (2)Scan “Bluetooth HID Mode”. Bluetooth HID Mode (3)Find “NETUM WF Scanner” from your bluetooth list and tap pair. Important Notes: Make sure the device is in range with Bluetooth turned on. • Pressing the scan button will initiate the attempts to connect. -
Page 9: Keyboard Language
For example If you use French Keyboard, scan command barcode of Keyboard Language “French keyboard ”. If you use a US keyboard you can ignore this step. * America EN keyboard French keyboard Italy keyboard Germany keyboard Portugal keyboard Spain keyboard Scanner will turn to sleep after idle/inactive for 3mins Idle Time Power Off... -
Page 10: Function Key Mapping
30Mins Disable sleep Mode When Function Key Mapping is enabled, function characters are sent over the keypad. Function Key Mapping $KEY#MO $KEY#M1 *Disable Function Key Mapping Enable Function Key Mapping LED Activity/Prompt Tone /Indication under different Connections LED Light Status Beep Pattern Indication Working Mode... - Page 11 2. How to change terminator to TAB ? downloaded from our of�icial website. Yes, you may go to our of�icial website” www.netum.net” to download the manual 3. Are there any barcodes for applying or removing pre�ix & suf�ix ? ,refer to the section of“ pre�ix and suf�ix” or turn to customer service for help.
- Page 12 Please do not hesitate to contact us if you need any other con�igurations. Note: Email: service@netum.net Contact Information Whatsapp: +86 188 2626 1132 Tel.: +0086 20-3222-8813 Add: 301,6 3/F, Building 1, No. 51 ,Xiangshan Avenue, Ningxi ST Zengcheng, GZ China...
Need help?
Do you have a question about the DS2800 and is the answer not in the manual?
Questions and answers