Table of Contents
Advertisement
en Basic operation
8.
ATTENTION!
If there is water on the cooking compartment floor
when operating the appliance at temperatures
above 120 °C, this will damage the enamel.
▶
Do not use the appliance if there is water on the
cooking compartment floor.
▶
Wipe away any water on the cooking compart-
ment floor before operation.
Apply the following settings:
Type of heating
Temperature
Cooking time
→ "Basic operation", Page 14
9.
Press
to start the operation.
8 Basic operation
8.1 Switching on the appliance
▶
Press
to switch the appliance on.
The
button lights up blue.
‒
a The Siemens logo appears in the display. A type of
heating and a temperature are then displayed.
8.2 Switching off the appliance
Switch your appliance off when you are not using it.
The appliance will switch itself off automatically if it is
not used for a certain period of time.
▶
Press
to switch the appliance off.
The light above the
‒
a The appliance switches off. Any functions currently
in progress are cancelled.
a The time or residual heat indicator appears in the
display.
8.3 Starting operation
You must start each cooking operation.
ATTENTION!
If there is water on the cooking compartment floor
when operating the appliance at temperatures above
120 °C, this will damage the enamel.
▶
Do not use the appliance if there is water on the
cooking compartment floor.
▶
Wipe away any water on the cooking compartment
floor before operation.
▶
Press
to start the operation.
a The settings, the run time and the heat-up line ap-
pear on the display.
8.4 Pausing or cancelling operation
You can briefly pause the operation and then continue.
If you cancel the operation completely, the settings are
reset.
1.
To pause the operation briefly:
Briefly press
‒
14
4D hot air
Maximum
30 minutes
button goes out.
.
Ventilate the kitchen while the appliance is heat-
‒
ing.
a When the cooking time has elapsed, a signal
sounds and the duration is at zero on the display.
10.
Press
to switch the appliance off.
11.
Once the appliance has cooled down, clean the
smooth surfaces in the cooking compartment with a
detergent solution and a dish cloth.
12.
Clean the accessories thoroughly using a detergent
solution and a dish cloth or soft brush.
13.
Empty the water tank and dry the cooking compart-
ment.
→ "Emptying the water tank", Page 19
Note: Following a power cut, the calibrated settings are
retained.
To adjust the appliance to a new installation location
after moving house, reset the basic settings to the fact-
ory settings. Carry out the procedures for initial start-up
and calibration again.
To continue the operation, press
‒
2.
To cancel the operation, press
a The operation stops and all of the settings are reset.
8.5 Setting an operating mode
Requirement: The appliance must be switched on.
1.
Press
.
The operating modes menu opens.
2.
Press the operating mode that you require.
Various options are available depending on the op-
erating mode.
3.
The selection can be changed using the rotary se-
lector.
Change any further settings depending on the selec-
tion.
4.
Press
to start.
8.6 Setting the type of heating and the
temperature
When you switch on the appliance, the types of heating
operating mode is set automatically.
1.
Turn the rotary selector to select the required type
of heating.
2.
Press the temperature.
3.
Use the rotary selector to set the temperature.
4.
Press
to start the operation.
a The appliance starts heating.
a The set type of heating, temperature and cooking
time/appliance run time are shown in the display.
5.
When the food is ready, press
appliance off.
Tip: The most suitable type of heating for your food
can be found in the type of heating description.
Note: You can also set a cooking time and an opera-
tion end time on the appliance.
→ "Time-setting options", Page 15
.
.
to switch the
Advertisement
Table of Contents
