Table of Contents
Advertisement
W4E420-CU03-36
3.2 Nominal data
Motor
M4E094-EA
Phase
1~
Nominal voltage / VAC
230
Frequency / Hz
60
Method of obtaining
ml
data
Valid for approval/
-
standard
-1
Speed (rpm) / min
1520
Power consumption / W
385
Current draw / A
1.68
Capacitor / µF
7
Capacitor voltage / VDB
450
Capacitor standard
S2 (CE)
Max. back pressure / Pa
100
Min. ambient
-25
temperature / °C
Max. ambient
55
temperature / °C
ml = Max. load · me = Max. efficiency · fa = Free air
cs = Customer specification · ce = Customer equipment
Subject to change
3.3 Technical description
Weight
8.7 kg
Size
420 mm
Motor size
94
Rotor surface
Painted black
Impeller material
PP plastic, galvanized sheet-metal plate
Fan housing material
Sheet steel, galvanized and coated with
black plastic (RAL 9005)
Guard grille material
Steel, coated with black plastic (RAL
9005)
Number of blades
5
Airflow direction
V
Direction of rotation
Counterclockwise, viewed toward rotor
Degree of protection
IP54
Insulation class
"F"
Moisture (F) /
H2
Environmental (H)
protection class
Ambient temperature
Occasional start-up at temperatures
note
between -40°C and -25°C is permitted.
For continuous operation at ambient
temperatures below -25°C (such as
refrigeration applications), use must be
made of a fan design with special low-
temperature bearings.
Installation position
Shaft horizontal or rotor on bottom; rotor
on top on request
Condensation
On rotor side
drainage holes
Mode
S1
Motor bearing
Ball bearing
Touch current
<= 3.5 mA
according to IEC
60990 (measuring
circuit Fig. 4, TN
system)
Item no. 16560-5-9970 · ENU · Change 241886 · Approved 2021-10-15 · Page 5 / 11
ebm-papst Mulfingen GmbH & Co. KG · Bachmühle 2 · D-74673 Mulfingen · Phone +49 (0) 7938 81-0 · Fax +49 (0) 7938 81-110 · info1@de.ebmpapst.com · www.ebmpapst.com
Operating instructions
Motor protection
with cable
Protection class
assignment
Motor capacitor
according to EN 60252-
1 in safety protection
class
Comment on CE
Approval
; Use the device in accordance with its degree of protection.
Information on surface quality
The surfaces of the products conform to the generally applicable industrial
standard. The surface quality may change during the production period.
This has no effect on strength, dimensional stability and dimensional
accuracy.
The color pigments in the paints used perceptibly react to UV light over
the course of time. The product is to be protected against UV radiation to
prevent the formation of patches and fading. Changes in color are not a
reason for complaint and are not covered by the warranty. UV radiation
in the frequency range and the intensity of natural solar radiation has no
effect on the technical properties of the products.
3.4 Mounting data
Any further mounting data required can be taken from the product
drawing or Section Chapter 4.1 Mechanical connection.
Strength class of
screws
For screw clearance, see Chapter 3.1 Product drawing
; Secure the screws against unintentional loosening (e.g. use self-
locking screws).
3.5 Transport and storage conditions
Max. permitted
ambient temp. for
motor (transport/
storage)
Min. permitted
ambient temp. for
motor (transport/
storage)
Thermal overload protector (TOP)
internally connected
Variable
I; If a protective earth is connected by
the customer
This component for installation may
have several local protection classes.
This information relates to this
component's basic design.
The final protection class is based on
the component's intended installation and
connection.
S2
Commissioning not permitted in the
European Economic Area
UL 1004-1; EAC; CSA C22.2 No. 100
With regard to cyclic speed loads, note that the rotating parts of
the device are designed for a maximum of one million load
cycles. If you have special questions, consult ebm-papst for
support.
8.8
+80 °C
-40 °C
Advertisement
Table of Contents
