Related Manuals for Wacker Neuson SM275-20W
Summary of Contents for Wacker Neuson SM275-20W
- Page 1 OPERATION & MAINTENANCE MANUAL Mini Loader SM275-20W SM275-20T Item 9200000150 & 9200000160 Revision...
-
Page 2: Table Of Contents
Table of Contents SAFETY SERVICE SPECIFICATIONS OPERATION ATTACHMENTS TRANSPORT MAINTENANCE TROUBLESHOOTING Page 2 of 19 Item – Rev(s): 9200000150 & 9200000160 – 101... -
Page 3: Safety
01 – SAFETY General Operation Read, understand, and follow instructions before starting the Machine. Improper use may result in injury. Keep hands, feet and clothing away from all moving parts. Wear appropriate clothing and PPE including but not limited to safety glasses, long pants, safety shoes, and hearing protection. - Page 4 Do not touch equipment or attachment parts that may be hot from operation. Allow to cool before attempting to maintain, adjust, or service. Never let children or untrained people operate or service the machine. Do not allow any person or animal near the machine or its attachments whilst in operation. Stop the machine if any person or animal approaches.
- Page 5 LOADING and UNLOADING Machine may be safely operated for loading and unloading to and from trailers intermittently, at angles greater than the operations manual specification of 15 degrees. Note that safe loading practices on weight location and distribution of the machine must be observed when loading and unloading at an angle.
-
Page 6: Service
03 – SERVICE Servicing, Preventative Maintenance, and Repairs should be performed by an Authorised Wacker Neuson Dingo Dealer in accordance with manufacturer recommendations. Before performing any service, repairs, maintenance, or adjustment, the machine must be shut down and isolated to prevent accidental starting. -
Page 7: Specifications
04 – SPECIFICATIONS Engine Make Water Cooled Diesel Power 20hp (17kw) Performance Hydraulic Pumps Pump Sizes 9 & 3.5cc Relief Pressure (AUX) 3000 psi (206 bar) Hydraulic Output 38 L/min Max Travel Speed 5 km/h Rated Lift Capacity 275kg WLL Wheel Motors –... - Page 8 Page 8 of 19 Item – Rev(s): 9200000150 & 9200000160 – 101...
-
Page 9: Operation
05 – OPERATION Become familiar with this manual and the engine manual. Before commencing operation each day perform the following pre start checks: Operating Instructions Read all the safety instructions and the pre start section of this manual and the engine manual before operating the machine. - Page 10 Work Area Ground conditions are firm and stable Sloping ground has been identified Holes have been identified and isolated Embankments have been marked Tree stumps, rocks and other hazards have been identified & removed or marked Water courses (dams, creeks, rivers) have been clearly marked Underground and aboveground service have been identified and isolated if necessary Site physical hazards have been identified &...
- Page 11 Failure to do so will affect the weight distribution, and can drastically reduce the stability and carrying capacity of the machine. A range of tyres to suit different applications, and equipment for water filling your tyres is available to purchase from your Authorised Wacker Neuson Dingo Dealer. Control Panel Pump selector...
- Page 12 The machine is capable of turning on the spot by applying equal power to each drive lever in opposite directions. Load Frame Lever To lower the load frame, slowly push the arm lever forward. To raise the load frame, slowly pull the arm lever backward. 4 in 1 Bucket The 4 in 1 bucket lever opens and closes the bucket.
-
Page 13: Attachments
Warning: The load frame may lower when in the raised position. To avoid this hazard always install cylinder locks or safety stand, available through your Authorised Wacker Neuson Dingo Dealer. 06 – ATTACHMENTS Connecting Use only Genuine Wacker Neuson Dingo attachments. -
Page 14: Transport
Disconnecting Lower attachment to the ground or onto a trailer. Turn the ignition key off to stop the engine. Move the auxiliary hydraulics lever forward, backward and back to neutral position to relieve hydraulic pressure at the hydraulic couplers. Slide collar back on the hydraulic coupler and disconnect attachment couplers from machine couplers (Note if this is difficult return to and repeat the 3 step). -
Page 15: Maintenance
It is essential to maintain the engine and the machine in accordance with manufacturer recommendations. Authorised Wacker Neuson Dingo Service Dealers provide expert servicing, preventative maintenance, and repair using Genuine Wacker Neuson Dingo parts to keep your machine running smoothly and to sustain validity of your warranty. - Page 16 When fitting new rubber tracks ensure the undercarriage components are in good condition and will support your new rubber tracks. Installing new tracks on a worn undercarriage may shorten their life. Wacker Neuson recommends the replacement of tracks be completed by an authorised Wacker Neuson service Agent Page 16 of 19 Item –...
-
Page 17: Troubleshooting
Inappropriate machine operation may also affect the life of your undercarriage. Take care when turning on hard surfaces such as concrete or asphalt. 09 – TROUBLESHOOTING Problem Possible Causes Corrective Action Starter does not Flat battery Charge battery. Replace if required crank engine Loose/corroded battery connections Check connections. - Page 18 Notes Page 18 of 19 Item – Rev(s): 9200000150 & 9200000160 – 101...
- Page 19 Notes Page 19 of 19 Item – Rev(s): 9200000150 & 9200000160 – 101...